lb11690 Sanyo Semiconductor Corporation, lb11690 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/5/586/sanyo_semiconductor_corporation_sml.jpg)
lb11690
Manufacturer Part Number
lb11690
Description
Pre-driver Ic For Brushless Motor Drive In Electric Bicycles
Manufacturer
Sanyo Semiconductor Corporation
Datasheet
1.LB11690.pdf
(19 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LB11690
Manufacturer:
ROHM
Quantity:
15 000
Pin Functions *: Items in parentheses refer to the LB11690H.
Pin name
(FRAME)
RFGND
W
PWM
V
U
GND
TOC
(NC)
RES
CP2
CP1
LVS
V12
V
WH
WL
UH
IN1
IN2
IN3
EI +
EI –
RC
RF
UL
VH
FV
HP
VB
VL
V5
OUT
OUT
OUT
CC
(19) (31)
(34) (36)
Pin No.
(6) (15)
10 (12)
11 (13)
12 (14)
13 (16)
14 (17)
15 (18)
16 (20)
17 (21)
18 (22)
19 (23)
20 (24)
21 (25)
22 (26)
23 (27)
24 (28)
25 (29)
26 (30)
27 (32)
28 (33)
29 (35)
8 (10)
9 (11)
30 (1)
1 (2)
2 (3)
3 (4)
4 (5)
7 (9)
5 (7)
6 (8)
—
Output current detection pin. Connect the low-resistance resistor RF between this pin and ground. The output current will be limited
to a value determined by the equation I
Hall sensor signal one-shot multi-pulse amplitude setting. Insert a resistor between this pin and the V5 pin, and a capacitor between
this pin and ground.
Ground
Ground sensing pin. Connect the ground side of the low-resistance resistor RF connected to the RF pin to this pin.
Low side n-channel power FET gate drive output
High side n-channel power FET source voltage detection
High side n-channel power FET gate drive output
Hall sensor signal inputs. Insert capacitors between these pins and ground for stabilization.
Reset input. Insert a resistor between this pin and the V5 pin, and a capacitor between this pin and ground.
Integrating amplifier noninverting input
Integrating amplifier inverting input
PWM waveform comparison (integrating amplifier output)
PWM oscillator frequency setting. Insert a capacitor between this pin and ground.
Hall sensor signal one-shot multi-pulse output
Hall sensor signal three-phase synthesized output (open collector output)
Charge pump capacitor connections. Connect a capacitor between pins CP1 and CP2.
Undervoltage protection voltage detection. To detect a voltage of 5 V or over, connect a zener diode in series to set the detection
voltage.
5 V power supply (control circuit power supply). Insert a capacitor between this pin and ground.
12 V power supply (UL, VL, and WL output block power supply). Insert a capacitor between this pin and ground.
Power supply. Insert a capacitor between this pin and ground for power supply stabilization.
Charge pump output (UH, VH, and WH output block power supply). Insert a capacitor between this pin and VCC.
The FRAME pin is connected to the IC lower surface metal frame. Both should be left electrically open during operation.
These pins are not connected to the IC internally in the package, and thus may be used for wiring connections.
OUT
LB11690, 11690H
= 0.1/RF. (Current limiter circuit)
Pin description
No. 7543-6/19