mt16hts25664hy-53e Micron Semiconductor Products, mt16hts25664hy-53e Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
mt16hts25664hy-53e
Manufacturer Part Number
mt16hts25664hy-53e
Description
2gb, 4gb X64, Dr 200-pin Ddr2 Sdram Sodimm
Manufacturer
Micron Semiconductor Products
Datasheet
1.MT16HTS25664HY-53E.pdf
(11 pages)
Table 6:
PDF: 09005aef821e5bf3/Source: 09005aef82198d54
HTS16C256_512x64H.fm - Rev. B 10/07 EN
DQS0#–DQS7#
DQS0–DQS7,
ODT0, ODT1
RAS#, CAS#,
CKE0, CKE1
DQ0–DQ63
DM0–DM7
CK0, CK0#
CK1, CK1#
BA0–BA2
SA0–SA1
Symbol
S0#, S1#
A0–A14
V
WE#
SDA
DDSPD
V
V
SCL
V
NC
REF
DD
SS
Pin Descriptions
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
Supply
Supply
Supply
Supply
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Type
I/O
I/O
I/O
–
Description
Address inputs: Provide the row address for ACTIVE commands and the column address, and
auto precharge bit (A10) for READ/WRITE commands, to select one location out of the memory
array in the respective bank. A10 sampled during a PRECHARGE command determines whether
the PRECHARGE applies to one device bank (A10 LOW, device bank selected by BA0–BA2) or all
device banks (A10 HIGH). The address inputs also provide the op-code during a LOAD MODE
command. A0–A13 (2GB) and A0–A14 (4GB).
Bank address inputs: BA0–BA2 define to which device bank an ACTIVE, READ, WRITE, or
PRECHARGE command is being applied. BA0–BA2 define which mode register, including MR,
EMR, EMR(2), and EMR(3), is loaded during the LOAD MODE command.
Clock: CK and CK# are differential clock inputs. All address and control input signals are
sampled on the crossing of the positive edge of CK and the negative edge of CK#. Output data
(DQ and DQS/DQS#) is referenced to the crossings of CK and CK#.
Clock enable: CKE (registered HIGH) activates and CKE (registered LOW) deactivates clocking
circuitry on the DDR2 SDRAM.
Data input mask: DM is an input mask signal for write data. Input data is masked when DM is
sampled HIGH along with that input data during a WRITE access. DM is sampled on both edges
of DQS. Although DM pins are input-only, the DM loading is designed to match that of DQ and
DQS pins.
On-die termination: ODT (registered HIGH) enables termination resistance internal to the
DDR2 SDRAM. When enabled, ODT is only applied to each of the following pins: DQ, DQS,
DQS#, and DM. The ODT input will be ignored if disabled via the LOAD MODE command.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command being entered.
Chip select: S# enables (registered LOW) and disables (registered HIGH) the command decoder.
All commands are masked when S# is registered HIGH. S# provides for external rank selection
on systems with multiple ranks. S# is considered part of the command code.
Presence-detect address inputs: These pins are used to configure the presence-detect
devices.
Serial clock for presence-detect: SCL is used to synchronize the presence-detect data transfer
to and from the module.
Data input/output: Bidirectional data bus.
Data strobe: Output with read data, input with write data for source synchronous operation.
Edge-aligned with read data, center-aligned with write data. DQS# is only used when
differential data strobe mode is enabled via the LOAD MODE command.
Serial presence-detect data: SDA is a bidirectional pin used to transfer addresses and data
into and out of the presence-detect portion of the module.
Power supply: +1.8 ±0.1V.
Serial EEPROM positive power supply: +1.7V to +3.6V.
SSTL_18 reference voltage (V
Ground.
No connect: These pins are not connected on the module.
2GB, 4GB (x64, DR) 200-Pin DDR2 SDRAM SODIMM
DD
/2).
4
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Pin Assignments and Descriptions
©2006 Micron Technology, Inc. All rights reserved.