h5ps2g43afr Hynix Semiconductor, h5ps2g43afr Datasheet - Page 37
![no-image](/images/manufacturer_photos/0/3/320/hynix_semiconductor_sml.jpg)
h5ps2g43afr
Manufacturer Part Number
h5ps2g43afr
Description
Ddr2 Sdram
Manufacturer
Hynix Semiconductor
Datasheet
1.H5PS2G43AFR.pdf
(40 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
h5ps2g43afr-S6C
Manufacturer:
HYNIX
Quantity:
9 500
Rev. 0.1 / November 2008
36. These parameters are specified per their average values, however it is understood that the following
relationship between the average timing and the absolute instantaneous timing holds at all times. (Min and
max of SPEC values are to be used for calculations in the table below.)
Example: For DDR2-667, tCH (abs), min = (0.48 x 3000 ps) - 125 ps = 1315 ps
37. tHP is the minimum of the absolute half period of the actual input clock. tHP is an input parameter but
not an input specification parameter. It is used in conjunction with tQHS to derive the DRAM output timing
tQH.
The value to be used for tQH calculation is determined by the following equation;
tHP = Min (tCH (abs), tCL (abs)),
where,
tCH (abs) is the minimum of the actual instantaneous clock HIGH time;
tCL (abs) is the minimum of the actual instantaneous clock LOW time;
38. tQHS accounts for:
1) The pulse duration distortion of on-chip clock circuits, which represents how well the actual tHP at the
input is transferred to the output; and
2) The worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the next
transition, both of which are independent of each other, due to data pin skew, output pattern effects, and
p-channel to n-channel variation of the output drivers
39. tQH = tHP? tQHS, where:
tHP is the minimum of the absolute half period of the actual input clock; and
tQHS is the specification value under the max column.
{The less half-pulse width distortion present, the larger the tQH value is; and the larger the valid data eye
will be.}
Examples:
1) If the system provides tHP of 1315 ps into a DDR2-667 SDRAM, the DRAM provides tQH of 975 ps min-
imum.
2) If the system provides tHP of 1420 ps into a DDR2-667 SDRAM, the DRAM provides tQH of 1080 ps
minimum.
40. When the device is operated with input clock jitter, this parameter needs to be derated by the actual
tERR(6-10per) of the input clock. (output deratings are relative to the SDRAM input clock.)
For example, if the measured jitter into a DDR2-667 SDRAM has tERR(6-10per),min = - 272 ps and
tERR(6-10per), max = + 293 ps, then tDQSCK, min (derated) = tDQSCK, min - tERR(6-10per),max = -
400 ps - 293 ps = - 693 ps and tDQSCK, max (derated) = tDQSCK, max - tERR(6-10per),min = 400 ps +
Absolute clock HIGH pulse width
Absolute clock LOW pulse width
Absolute clock period
Parameter
Symbol
tCK (abs)
tCH (abs)
tCL (abs)
tCH (avg), min* tCK (avg), min +
tCL (avg), min* tCK (avg), min +
tCK (avg), min + tJIT (per), min
tJIT (per), min
tJIT (per), min
min
tCL (avg), max* tCK (avg), max +
tCK (avg), max + tJIT (per), max
tCH (avg), max* tCK (avg), max
+ tJIT (per), max
tJIT (per), max
max
H5PS2G43AFR
H5PS2G83AFR
Units
ps
ps
ps
37