IDT7026L IDT [Integrated Device Technology], IDT7026L Datasheet - Page 16

• Manufacturer Part Number: IDT7026L
• Description: HIGH-SPEED 16K x 16 DUAL-PORT STATIC RAM
• Manufacturer: IDT [Integrated Device Technology]

IDT7026S/L
HIGH-SPEED 16K x 16 DUAL-PORT STATIC RAM
CMOS Static RAM and can be read from, or written to, at the
same time with the only possible conflict arising from the
simultaneous writing of, or a simultaneous READ/WRITE of,
a non-semaphore location. Semaphores are protected against
such ambiguous situations and may be used by the system
program to avoid any conflicts in the non-semaphore portion
of the Dual-Port RAM. These devices have an automatic
power-down feature controlled by
enable, and
pins control on-chip power down circuitry that permits the
respective port to go into standby mode when not selected.
This is the condition which is shown in Truth Table where
and
processors or controllers and are typically very high-speed
systems which are software controlled or software intensive.
These systems can benefit from a performance increase
offered by the IDT7026's hardware semaphores, which pro-
vide a lockout mechanism without requiring complex pro-
gramming.
maximum in system flexibility by permitting shared resources
to be allocated in varying configurations. The IDT7026 does
not use its semaphore flags to control any resources through
hardware, thus allowing the system designer total flexibility in
system architecture.
common methods of hardware arbitration is that wait states
are never incurred in either processor. This can prove to be
a major advantage in very high-speed systems.
HOW THE SEMAPHORE FLAGS WORK
independent of the Dual-Port RAM. These latches can be
used to pass a flag, or token, from one port to the other to
indicate that a shared resource is in use. The semaphores
provide a hardware assist for a use assignment method called
“Token Passing Allocation.” In this method, the state of a
semaphore latch is used as a token indicating that shared
resource is in use. If the left processor wants to use this
resource, it requests the token by setting the latch. This
processor then verifies its success in setting the latch by
reading it. If it was successful, it proceeds to assume control
over the shared resource. If it was not successful in setting the
latch, it determines that the right side processor has set the
latch first, has the token and is using the shared resource. The
left processor can then either repeatedly request that
semaphore’s status or remove its request for that semaphore
to perform another task and occasionally attempt again to
gain control of the token via the set and test sequence. Once
the right side has relinquished the token, the left side should
succeed in gaining control.
quested by writing a zero into a semaphore latch and is
released when the same side writes a one to that latch.
separate memory space from the Dual-Port RAM. This
Systems which can best use the IDT7026 contain multiple
Software handshaking between processors offers the
An advantage of using semaphores rather than the more
The semaphore logic is a set of eight latches which are
The semaphore flags are active LOW. A token is re-
The eight semaphore flags reside within the IDT7026 in a
SEM
are both HIGH.
SEM
, the semaphore enable. The
CE
, the Dual-Port RAM
CE
and
SEM
CE
6.17
address space is accessed by placing a low input on the
pin (which acts as a chip select for the semaphore flags) and
using the other control pins (Address,
would be used in accessing a standard Static RAM. Each of
the flags has a unique address which can be accessed by
either side through address pins A0 – A2. When accessing the
semaphores, none of the other address pins has any effect.
a low level is written into an unused semaphore location, that
flag will be set to a zero on that side and a one on the other side
(see Table III). That semaphore can now only be modified by
the side showing the zero. When a one is written into the same
location from the same side, the flag will be set to a one for both
sides (unless a semaphore request from the other side is
pending) and then can be written to by both sides. The fact that
the side which is able to write a zero into a semaphore
subsequently locks out writes from the other side is what
makes semaphore flags useful in interprocessor communica-
tions. (A thorough discussing on the use of this feature follows
shortly.) A zero written into the same location from the other
side will be stored in the semaphore request latch for that side
until the semaphore is freed by the first side.
data bits so that a flag that is a one reads as a one in all data
bits and a flag containing a zero reads as all zeros. The read
value is latched into one side’s output register when that side's
semaphore select (
active. This serves to disallow the semaphore from changing
state in the middle of a read cycle due to a write cycle from the
other side. Because of this latch, a repeated read of a
semaphore in a test loop must cause either signal (
to go inactive or the output will never change.
phore in order to guarantee that no system level contention
will occur. A processor requests access to shared resources
by attempting to write a zero into a semaphore location. If the
semaphore is already in use, the semaphore request latch will
contain a zero, yet the semaphore flag will appear as one, a
fact which the processor will verify by the subsequent read
(see Table III). As an example, assume a processor writes a
zero to the left port at a free semaphore location. On a
subsequent read, the processor will verify that it has written
successfully to that location and will assume control over the
resource in question. Meanwhile, if a processor on the right
side attempts to write a zero to the same semaphore flag it will
fail, as will be verified by the fact that a one will be read from
that semaphore on the right side during subsequent read.
Had a sequence of READ/WRITE been used instead, system
contention problems could have occurred during the gap
between the read and write cycles.
be followed by either repeated reads or by writing a one into
the same location. The reason for this is easily understood by
looking at the simple logic diagram of the semaphore flag in
Figure 4. Two semaphore request latches feed into a sema-
phore flag. Whichever latch is first to present a zero to the
semaphore flag will force its side of the semaphore flag LOW
and the other side HIGH. This condition will continue until a
When writing to a semaphore, only data pin D
When a semaphore flag is read, its value is spread into all
A sequence WRITE/READ must be used by the sema-
It is important to note that a failed semaphore request must
MILITARY AND COMMERCIAL TEMPERATURE RANGES
SEM
) and output enable (
OE
, and R/
OE
0
) signals go
SEM
W
is used. If
) as they
or
SEM
16
OE
)