a10v20b Actel Corporation, a10v20b Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
a10v20b
Manufacturer Part Number
a10v20b
Description
Act? 1 Series Fpgas
Manufacturer
Actel Corporation
Datasheet
1.A10V20B.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
a10v20b-PLG68C
Manufacturer:
Microsemi SoC
Quantity:
10 000
Company:
Part Number:
a10v20b-PLG84C
Manufacturer:
Microsemi SoC
Quantity:
10 000
ACT 1 Timing Modul e*
Pred ictab le Perfor m anc e: T i ght D e l a y
Distribu tions
Propagation delay between logic modules depends on the
resistive and capacitive loading of the routing tracks, the
interconnect elements, and the module inputs being driven.
Propagation delay increases as the length of routing tracks,
the number of interconnect elements, or the number of
inputs increases.
From a design perspective, the propagation delay can be
statistically correlated or modeled by the fanout (number of
loads) driven by a module. Higher fanout usually requires
some paths to have longer routing tracks.
The ACT 1 family delivers a very tight fanout delay
distribution. This tight distribution is achieved in two ways: by
decreasing the delay of the interconnect elements and by
decreasing the number of interconnect elements per path.
Actel’s patented PLICE antifuse offers a very low
resistive/capacitive interconnect. The ACT 1 family’s
antifuses, fabricated in 1.0 micron lithography, offer nominal
levels of 200 ohms resistance and 7.5 femtofarad (fF)
capacitance per antifuse.
The ACT 1 fanout distribution is also tight due to the low
number of antifuses required for each interconnect path. The
ACT 1 family’s proprietary architecture limits the number of
antifuses per path to a maximum of four, with 90% of
interconnects using two antifuses.
1-292
CLOCK
ARRAY
* Values shown for ACT 1 ‘–3 speed’ devices at worst-case commercial conditions.
I/O Module
F
MAX
t
Input Delay
CKH
= 70 MHz
= 5.6 ns
t
INYL
= 3.1 ns
FO = 128
t
t
t
t
IRD2
IRD4
IRD8
IRD1
= 1.4 ns
= 0.9 ns
= 3.1 ns
= 6.6 ns
Internal Delays
Logic Module
t
t
CO
PD
= 2.9 ns
= 2.9 ns
Timing Charact eris t ics
Timing characteristics for ACT 1 devices fall into three
categories: family dependent, device dependent, and design
dependent. The input and output buffer characteristics are
common to all ACT 1 family members. Internal routing delays
are device dependent. Design dependency means actual delays
are not determined until after placement and routing of the
user design is complete. Delay values may then be determined
by using the DirectTime Analyzer utility or performing
simulation with post-layout delays.
Critical Nets and Typical Nets
Propagation delays are expressed only for typical nets, which
are used for initial design performance evaluation. Critical
net delays can then be applied to the most time-critical paths.
Critical nets are determined by net property assignment prior
to placement and routing. Up to 6% of the nets in a design may
be designated as critical, while 90% of the nets in a design are
typical.
Long Tracks
Some nets in the design use long tracks. Long tracks are
special routing resources that span multiple rows, columns, or
modules.
antifuse connections. This increases capacitance and
resistance, resulting in longer net delays for macros
connected to long tracks. Typically, up to 6% of nets in a fully
utilized device require long tracks. Long tracks contribute
approximately 5 ns to 10 ns delay. This additional delay is
represented statistically in higher fanout (FO=8) routing
delays in the data sheet specifications section.
t
t
t
t
RD4
RD1
RD2
RD8
Predicted
Routing
Delays
Long tracks employ three and sometimes four
= 3.1 ns
= 0.9 ns
= 1.4 ns
= 6.6 ns
I/O Module
Output Delay
t
ENHZ
t
DLH
= 11.6 ns
= 6.7 ns