SC16IS740IPW PHILIPS [NXP Semiconductors], SC16IS740IPW Datasheet - Page 24
![no-image](/images/no-image-200.jpg)
SC16IS740IPW
Manufacturer Part Number
SC16IS740IPW
Description
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.SC16IS740IPW.pdf
(62 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16IS740IPW
Manufacturer:
NXP
Quantity:
505
Part Number:
SC16IS740IPW
Manufacturer:
NXP
Quantity:
20 000
Company:
Part Number:
SC16IS740IPW,112
Manufacturer:
JAMICON
Quantity:
101
Part Number:
SC16IS740IPWR
Manufacturer:
TI/德州仪器
Quantity:
20 000
NXP Semiconductors
SC16IS740_750_760_5
Product data sheet
8.4 Line Control Register (LCR)
[1]
This register controls the data communication format. The word length, number of stop
bits, and parity type are selected by writing the appropriate bits to the LCR.
shows the Line Control Register bit settings.
Table 12.
Bit
7
6
5
4
3
2
1:0
FIFO reset requires at least two XTAL1 clocks, therefore, they cannot be reset without the presence of the
XTAL1 clock.
Symbol
LCR[7]
LCR[6]
LCR[5]
LCR[4]
LCR[3]
LCR[2]
LCR[1:0]
Line Control Register bits description
Rev. 05 — 16 November 2006
Single UART with I
Description
divisor latch enable
Break control bit. When enabled, the break control bit causes a break
condition to be transmitted (the TX output is forced to a logic 0 state).
This condition exists until disabled by setting LCR[6] to a logic 0.
Set parity. LCR[5] selects the forced parity format (if LCR[3] = 1).
parity type select
parity enable
Number of stop bits. Specifies the number of stop bits.
Word length bits 1, 0. These two bits specify the word length to be
transmitted or received; see
logic 0 = divisor latch disabled (normal default condition)
logic 1 = divisor latch enabled
logic 0 = no TX break condition (normal default condition).
logic 1 = forces the transmitter output (TX) to a logic 0 to alert the
communication terminal to a line break condition
logic 0 = parity is not forced (normal default condition).
LCR[5] = logic 1 and LCR[4] = logic 0: parity bit is forced to a logical 1
for the transmit and receive data.
LCR[5] = logic 1 and LCR[4] = logic 1: parity bit is forced to a logical 0
for the transmit and receive data.
logic 0 = odd parity is generated (if LCR[3] = 1)
logic 1 = even parity is generated (if LCR[3] = 1)
logic 0 = no parity (normal default condition).
logic 1 = a parity bit is generated during transmission and the receiver
checks for received parity
0 to 1 stop bit (word length = 5, 6, 7, 8)
1 to 1.5 stop bits (word length = 5)
1 = 2 stop bits (word length = 6, 7, 8)
2
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
SC16IS740/750/760
Table
15.
© NXP B.V. 2006. All rights reserved.
Table 12
24 of 62