SC16C650BIBS PHILIPS [NXP Semiconductors], SC16C650BIBS Datasheet
SC16C650BIBS
Related parts for SC16C650BIBS
SC16C650BIBS Summary of contents
Page 1
SC16C650B 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder Rev. 03 — 10 December 2004 1. General description The SC16C650B is a Universal Asynchronous Receiver and Transmitter (UART) used for serial data communications. ...
Page 2
... Description SC16C650BIA44 PLCC44 plastic leaded chip carrier; 44 leads SC16C650BIB48 LQFP48 plastic low profile quad flat package; 48 leads; body 7 SC16C650BIBS HVQFN32 plastic thermal enhanced very thin quad flat package; no leads; 32 terminals; body 5 SC16C650BIN40 DIP40 plastic dual in-line package; 40 leads (600 mil) ...
Page 3
Philips Semiconductors 4. Block diagram SC16C650B D0–D7 DATA BUS IOR, IOR AND IOW, IOW CONTROL LOGIC RESET A0–A2 REGISTER CS0, CS1, CS2 SELECT AS LOGIC DDIS INT TXRDY RXRDY INTERRUPT CONTROL LOGIC Fig 1. Block diagram. 9397 750 14451 Product ...
Page 4
Philips Semiconductors 5. Pinning information 5.1 Pinning Fig 2. PLCC44 pin configuration. 9397 750 14451 Product data UART with 32-byte FIFOs and IrDA encoder/decoder RCLK SC16C650BIA44 n. CS0 ...
Page 5
... RCLK 5 n.c. 6 SC16C650BIB48 CS0 9 CS1 10 CS2 11 BAUDOUT 12 terminal 1 index area RCLK 4 SC16C650BIBS RX 5 (top view BAUDOUT 8 Rev. 03 — 10 December 2004 SC16C650B 36 n.c. 35 RESET 34 OUT1 33 DTR 32 RTS 31 OUT2 30 INT 29 RXRDY ...
Page 6
Philips Semiconductors Fig 5. DIP40 pin configuration. 5.2 Pin description Table 2: Pin description Symbol Pin PLCC44 LQFP48 HVQFN32 DIP40 A0-A2 31, 30, 28, 27, 18, 17 BAUDOUT 9397 ...
Page 7
Philips Semiconductors Table 2: Pin description …continued Symbol Pin PLCC44 LQFP48 HVQFN32 DIP40 CS0, CS1, 14, 15, 9, 10, - CS2 CTS D7-D0 9-2 4-2, 3-1, 32-28 8-1 47-43 DCD 42 ...
Page 8
Philips Semiconductors Table 2: Pin description …continued Symbol Pin PLCC44 LQFP48 HVQFN32 DIP40 OUT1, 38 OUT2 OUT - - 23 RCLK IOR IOR RESET ...
Page 9
Philips Semiconductors Table 2: Pin description …continued Symbol Pin PLCC44 LQFP48 HVQFN32 DIP40 TXRDY GND IOW IOW 20 ...
Page 10
Philips Semiconductors 6. Functional description The SC16C650B provides serial asynchronous receive data synchronization, parallel-to-serial and serial-to-parallel data conversions for both the transmitter and receiver sections. These functions are necessary for converting the serial data stream into parallel data that is ...
Page 11
Philips Semiconductors 6.1 Internal registers The SC16C650B provides 17 internal registers for monitoring and control. These registers are shown in in the standard 16C550. These registers function as data holding registers (THR/RHR), interrupt status and control registers (IER/ISR), a FIFO ...
Page 12
Philips Semiconductors a time-out function to ensure data is delivered to the external CPU. An interrupt is generated whenever the Receive Holding Register (RHR) has not been read following the loading of a character or the receive trigger level has ...
Page 13
Philips Semiconductors characters are not placed (stacked) in the user accessible RX data buffer or FIFO. When using a software flow control the Xon/Xoff characters cannot be used for data transfer. In the event that the receive buffer is overfilling ...
Page 14
Philips Semiconductors 6.7 Programmable baud rate generator The SC16C650B supports high speed modem technologies that have increased input data rates by employing data compression schemes. For example, a 33.6 kbit/s modem that employs data compression may require a 115.2 kbit/s ...
Page 15
Philips Semiconductors Table 5: Using 1.8432 MHz crystal Desired baud rate 50 75 110 134.5 150 300 600 1200 1800 2000 2400 3600 4800 7200 9600 19200 38400 56000 XTAL1 XTAL2 Fig 7. Baud rate generator circuitry. 9397 750 14451 ...
Page 16
Philips Semiconductors 6.8 DMA operation The SC16C650B FIFO trigger level provides additional flexibility to the user for block mode operation. The user can optionally operate the transmit and receive FIFOs in the DMA mode (FCR[3]). The DMA mode affects the ...
Page 17
Philips Semiconductors In this mode, the receiver and transmitter interrupts are fully operational. The Modem Control Interrupts are also operational. However, the interrupts can only be read using lower four bits of the Modem Status Register (MSR[0:3]) instead of the ...
Page 18
Philips Semiconductors 7. Register descriptions Table 8 The assigned bit functions are more fully defined in Table 8: SC16C650B internal registers Shaded bits are only accessible when EFR[4] is set. [ Register Default [2] General Register Set ...
Page 19
Philips Semiconductors 7.1 Transmit (THR) and Receive (RHR) Holding Registers The serial transmitter section consists of an 8-bit Transmit Hold Register (THR) and Transmit Shift Register (TSR). The status of the THR is provided in the Line Status Register (LSR). ...
Page 20
Philips Semiconductors Table 9: Bit 7.2.1 IER versus Receive FIFO interrupt mode operation When the receive FIFO (FCR[0] = logic 1), and receive interrupts (IER[0] = logic 1) are enabled, the receive interrupts and register status will ...
Page 21
Philips Semiconductors 7.3 FIFO Control Register (FCR) This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger levels, and select the DMA mode. 7.3.1 DMA mode Mode 0 (FCR bit 3 = 0): receive ...
Page 22
Philips Semiconductors Table 10: Bit Table 11: FCR[ Table 12: FCR[ 9397 750 14451 Product data UART with 32-byte FIFOs and IrDA encoder/decoder FIFO Control Register bits description Symbol ...
Page 23
Philips Semiconductors 7.4 Interrupt Status Register (ISR) The SC16C650B provides six levels of prioritized interrupts to minimize external software interaction. The Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the ISR ...
Page 24
Philips Semiconductors 7.5 Line Control Register (LCR) The Line Control Register is used to specify the asynchronous data communication format. The word length, the number of stop bits, and the parity are selected by writing the appropriate bits in this ...
Page 25
Philips Semiconductors Table 16: LCR[ Table 17: LCR[ Table 18: LCR[ 7.6 Modem Control Register (MCR) This register controls the interface with the modem or a peripheral device. ...
Page 26
Philips Semiconductors Table 19: Bit 9397 750 14451 Product data UART with 32-byte FIFOs and IrDA encoder/decoder Modem Control Register bits description Symbol Description MCR[5] INT typ select. Logic 0 = Enable active or ...
Page 27
Philips Semiconductors 7.7 Line Status Register (LSR) This register provides the status of data transfers between the SC16C650B and the CPU. Table 20: Bit 9397 750 14451 Product data UART with 32-byte FIFOs ...
Page 28
Philips Semiconductors Table 20: Bit 0 7.8 Modem Status Register (MSR) This register provides the current state of the control interface signals from the modem, or other peripheral device to which the SC16C650B is connected. Four bits of this register ...
Page 29
Philips Semiconductors Table 21: Bit 1 0 [1] Whenever any MSR bit 0:3 is set to logic 1, a Modem Status Interrupt will be generated. 7.9 Scratchpad Register (SPR) The SC16C650B provides a temporary data register to store 8 bits ...
Page 30
Philips Semiconductors Table 22: Bit 5 4 3:0 Table 23: Cont [1] When using a software flow control the Xon/Xoff characters cannot be used for data transfer. 9397 750 14451 ...
Page 31
Philips Semiconductors 7.11 SC16C650B external reset conditions Table 24: Register IER ISR LCR MCR LSR MSR FCR EFR Table 25: Output TX RTS DTR RXRDY TXRDY INT 8. Limiting values Table 26: In accordance with the Absolute Maximum Rating System ...
Page 32
Philips Semiconductors 9. Static characteristics Table 27: DC electrical characteristics + 2 5.0 V 10%, unless otherwise specified. amb CC Symbol Parameter V LOW-level clock input voltage IL(CK) ...
Page 33
Philips Semiconductors 10. Dynamic characteristics Table 28: AC electrical characteristics + 2 10%, unless otherwise specified. amb CC Symbol Parameter clock pulse duration ...
Page 34
Philips Semiconductors Table 28: AC electrical characteristics + 2 10%, unless otherwise specified. amb CC Symbol Parameter t delay from start to reset TXRDY 28d t ...
Page 35
Philips Semiconductors A0– CS2 CS1–CS0 t 13d t 14d IOW, IOW D0–D7 Fig 10. General write timing when using AS signal. A0–A2 ADDRESS IOR D0–D7 Fig 11. General read timing ...
Page 36
Philips Semiconductors A0–A2 ADDRESS IOW D0–D7 Fig 12. General write timing when AS is tied to GND. IOW ACTIVE RTS CHANGE OF STATE DTR DCD CTS DSR INT IOR RI Fig 13. Modem input/output timing. 9397 750 ...
Page 37
Philips Semiconductors t 2w EXTERNAL CLOCK Fig 14. External clock timing. start RX INT IOR Fig 15. Receive timing. 9397 750 14451 Product data UART with 32-byte FIFOs and IrDA encoder/decoder bit data bits (0 to ...
Page 38
Philips Semiconductors START BIT RX RXRDY IOR Fig 16. Receive ready timing in non-FIFO mode. START BIT RX RXRDY IOR Fig 17. Receive ready timing in FIFO mode. 9397 750 14451 Product data UART with 32-byte FIFOs and IrDA encoder/decoder ...
Page 39
Philips Semiconductors start TX INT active IOW Fig 18. Transmit timing. START BIT TX ACTIVE IOW D0-D7 BYTE #1 TXRDY Fig 19. Transmit ready timing in non-FIFO mode. 9397 750 14451 Product data UART with 32-byte FIFOs and IrDA encoder/decoder ...
Page 40
Philips Semiconductors START BIT TX ACTIVE IOW D0–D7 BYTE #16 t 27d TXRDY Fig 20. Transmit ready timing in FIFO mode (DMA mode ‘1’). 9397 750 14451 Product data UART with 32-byte FIFOs and IrDA encoder/decoder DATA BITS (5-8) D0 ...
Page 41
Philips Semiconductors start TX data 0 IrDA TX data bit time Fig 21. Infrared transmit timing. IrDA RX data bit time RX data 0 start Fig 22. Infrared receive timing. 9397 750 14451 Product data UART with 32-byte FIFOs and ...
Page 42
Philips Semiconductors 11. Package outline PLCC44: plastic leaded chip carrier; 44 leads pin 1 index DIMENSIONS (mm dimensions are derived from the original inch dimensions) A ...
Page 43
Philips Semiconductors LQFP48: plastic low profile quad flat package; 48 leads; body 1 pin 1 index DIMENSIONS (mm are the original dimensions) A ...
Page 44
Philips Semiconductors HVQFN32: plastic thermal enhanced very thin quad flat package; no leads; 32 terminals; body 0.85 mm terminal 1 index area terminal 1 index area 32 DIMENSIONS (mm ...
Page 45
Philips Semiconductors DIP40: plastic dual in-line package; 40 leads (600 mil pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions UNIT max. min. max. 1.70 mm 4.7 ...
Page 46
Philips Semiconductors 12. Soldering 12.1 Introduction This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages (document order number 9398 652 ...
Page 47
Philips Semiconductors – for packages with a thickness – for packages with a thickness < 2.5 mm and a volume • below 240 C (SnPb process) or below 260 C (Pb-free process) for packages with a thickness < 2.5 mm ...
Page 48
Philips Semiconductors 12.4 Package related soldering information Table 29: Mounting Through-hole mount Through-hole- surface mount Surface mount For more detailed information on the BGA packages refer to the (LF)BGA Application Note [1] (AN01026); order a copy from your Philips Semiconductors ...
Page 49
Philips Semiconductors 13. Revision history Table 30: Revision history Rev Date CPCN Description 03 20041210 - Product data (9397 750 14451) Modifications: • There is no modification to the data sheet. However, reader is advised to refer to AN10333 (Rev. ...
Page 50
Philips Semiconductors 14. Data sheet status [1] Level Data sheet status Product status I Objective data Development II Preliminary data Qualification III Product data Production [1] Please consult the most recently issued data sheet before initiating or completing a design. ...
Page 51
Philips Semiconductors Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features . . . . . . . . . ...