S29GL256N SPANSION [SPANSION], S29GL256N Datasheet - Page 53
![no-image](/images/no-image-200.jpg)
S29GL256N
Manufacturer Part Number
S29GL256N
Description
MirrorBit Flash Family
Manufacturer
SPANSION [SPANSION]
Datasheet
1.S29GL256N.pdf
(110 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
S29GL256N10FAI010
Manufacturer:
SPANSION
Quantity:
9 944
Company:
Part Number:
S29GL256N10FAI020
Manufacturer:
SPANSION
Quantity:
9 983
Company:
Part Number:
S29GL256N10FFI01
Manufacturer:
SPANSION
Quantity:
2 165
Company:
Part Number:
S29GL256N10FFI010
Manufacturer:
INTEL
Quantity:
31
Part Number:
S29GL256N10FFI010
Manufacturer:
CYPRESS/赛普拉斯
Quantity:
20 000
Company:
Part Number:
S29GL256N10FFI02
Manufacturer:
SPANSION
Quantity:
132
Part Number:
S29GL256N10FFI020E
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S29GL256N10TFI01
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S29GL256N10TFI010
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S29GL256N10TFI010H
Manufacturer:
SPANSIO
Quantity:
20 000
Common Flash Memory Interface (CFI)
May 13, 2004 27631A4
Write Protect (WP#)
Hardware Data Protection
The Write Protect function provides a hardware method of protecting the first or
last sector group without using V
by the WP#/ACC input.
If the system asserts V
erase functions in the first or last sector group independently of whether those
sector groups were protected or unprotected using the method described in“Ad-
vanced Sector Protection” section on page 46. Note that if WP#/ACC is at V
when the device is in the standby mode, the maximum input load current is in-
creased. See the table in “DC Characteristics” section on page 86.
If the system asserts V
whether the first or last sector was previously set to be protected or un-
protected using the method described in “Sector Group Protection and
Unprotection”. Note that WP# has an internal pullup; when uncon-
nected, WP# is at V
The command sequence requirement of unlock cycles for programming or erasing
provides data protection against inadvertent writes (refer to Tables
command definitions). In addition, the following hardware data protection mea-
sures prevent accidental erasure or programming, which might otherwise be
caused by spurious system level signals during V
transitions, or from system noise.
Low V
When V
tects data during V
internal program/erase circuits are disabled, and the device resets to the read
mode. Subsequent writes are ignored until V
must provide the proper signals to the control pins to prevent unintentional writes
when V
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write
cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# = V
V
logical one.
Power-Up Write Inhibit
If WE# = CE# = V
commands on the rising edge of WE#. The internal state machine is automatically
reset to the read mode on power-up.
The Common Flash Interface (CFI) specification outlines device and host system
software interrogation handshake, which allows specific vendor-specified soft-
ware algorithms to be used for entire families of devices. Software support can
IH
. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a
CC
CC
CC
is less than V
is greater than V
A d v a n c e
Write Inhibit
IL
CC
and OE# = V
IH
power-up and power-down. The command register and all
S29GLxxxN MirrorBitTM Flash Family
IL
LKO
.
on the WP#/ACC pin, the device disables program and
, the device does not accept any write cycles. This pro-
LKO
IH
I n f o r m a t i o n
on the WP#/ACC pin, the device reverts to
.
ID
IH
. Write Protect is one of two functions provided
during power up, the device does not accept
CC
is greater than V
CC
power-up and power-down
IL
, CE# = V
LKO
16
. The system
IH
and
or WE# =
17
for
IL
53