PCF80C562-12WP PHILIPS [NXP Semiconductors], PCF80C562-12WP Datasheet - Page 5

• Manufacturer Part Number: PCF80C562-12WP
• Description: Single-chip 8-bit microcontroller
• Manufacturer: PHILIPS [NXP Semiconductors]

1. To avoid “latch-up” effect at power-on, the voltage on any pin at any time must not be higher or lower than V
Philips Semiconductors
PIN DESCRIPTION
NOTE:
1992 Jan 08
V
STADC
PWM0
PWM1
EW
P0.0–P0.7
P1.0–P1.7
P2.0–P2.7
P3.0–P3.7
P4.0–P4.7
P5.0–P5.7
RST
XTAL1
XTAL2
V
PSEN
ALE
EA
AV
AV
AV
AV
MNEMONIC
DD
SS
Single-chip 8-bit microcontroller
respectively.
REF–
REF+
SS
DD
PIN NO.
68–62,
57–50
16–23
16–23
16–19
39–46
24–31
13, 14
36, 37
7–14
7–12
20
21
24
25
26
27
28
29
30
31
15
35
34
47
48
49
58
59
60
61
2
3
4
5
6
1
TYPE
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
Digital Power Supply: +5V power supply pin during normal operation, idle and power-down mode.
Start ADC Operation: Input starting analog to digital conversion (ADC operation can also be started
by software).
Pulse Width Modulation: Output 0.
Pulse Width Modulation: Output 1.
Enable Watchdog Timer: Enable for T3 watchdog timer and disable power-down mode.
Port 0: Port 0 is an 8-bit open-drain bidirectional I/O port. Port 0 pins that have 1s written to them float
and can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data
bus during accesses to external program and data memory. In this application it uses strong internal
pull-ups when emitting 1s.
Port 1: 8-bit I/O port. Alternate functions include:
Port 2: 8-bit quasi-bidirectional I/O port.
Alternate function: High-order address byte for external memory (A08–A15).
Port 3: 8-bit quasi-bidirectional I/O port. Alternate functions include:
Port 4: 8-bit quasi-bidirectional I/O port. Alternate functions include:
Port 5: 8-bit input port.
Reset: Input to reset the 87C552. It also provides a reset pulse as output when timer T3 overflows.
Crystal Input 1: Input to the inverting amplifier that forms the oscillator, and input to the internal clock
generator. Receives the external clock signal when an external oscillator is used.
Crystal Input 2: Output of the inverting amplifier that forms the oscillator. Left open–circuit when an
external clock is used.
Digital ground.
Program Store Enable: Active-low read strobe to external program memory.
Address Latch Enable: Latches the low byte of the address during accesses to external memory. It is
activated every six oscillator periods. During an external data memory access, one ALE pulse is
skipped. ALE can drive up to eight LS TTL inputs and handles CMOS inputs without an external
pull-up.
External Access: When EA is held at TTL level high, the CPU executes out of the internal program
ROM provided the program counter is less than 8192. When EA is held at TTL low level, the CPU
executes out of external program memory. EA is not allowed to float.
Analog to Digital Conversion Reference Resistor: Low-end.
Analog to Digital Conversion Reference Resistor: High-end.
Analog Ground
Analog Power Supply
(P1.0–P1.7): Quasi-bidirectional port pins.
CT0I–CT3I (P1.0–P1.3): Capture timer input signals for timer T2.
T2 (P1.4): T2 event input
RT2 (P1.5): T2 timer reset signal. Rising edge triggered.
RxD(P3.0): Serial input port.
TxD (P3.1): Serial output port.
INT0 (P3.2): External interrupt.
INT1 (P3.3): External interrupt.
T0 (P3.4): Timer 0 external input.
T1 (P3.5): Timer 1 external input.
WR (P3.6): External data memory write strobe.
RD (P3.7): External data memory read strobe.
CMSR0–CMSR5 (P4.0–P4.5): Timer T2 compare and set/reset outputs on a match with timer T2.
CMT0, CMT1 (P4.6, P4.7): Timer T2 compare and toggle outputs on a match with timer T2.
ADC0–ADC7 (P5.0–P5.7): Alternate function: Eight input channels to ADC.
5
NAME AND FUNCTION
DD
80C562/83C562
+0.5V or V
Product specification
SS
– 0.5V,