XC2S100-5CS144I XILINX [Xilinx, Inc], XC2S100-5CS144I Datasheet - Page 32

• Manufacturer Part Number: XC2S100-5CS144I
• Description: Spartan-II FPGA Family
• Manufacturer: XILINX [Xilinx, Inc]

Using Block RAM Features
The Spartan-II FPGA family provides dedicated blocks of
on-chip, true dual-read/write port synchronous RAM, with
4096 memory cells. Each port of the block RAM memory
can be independently configured as a read/write port, a
read port, a write port, and can be configured to a specific
data width. The block RAM memory offers new capabilities
allowing the FPGA designer to simplify designs.
Operating Modes
Block RAM memory supports two operating modes.
•
•
Read Through (One Clock Edge)
The read address is registered on the read port clock edge
and data appears on the output after the RAM access time.
Some memories may place the latch/register at the outputs
depending on the desire to have a faster clock-to-out versus
setup time. This is generally considered to be an inferior
solution since it changes the read operation to an
asynchronous function with the possibility of missing an
address/control line transition during the generation of the
read pulse clock.
Write Back (One Clock Edge)
The write address is registered on the write port clock edge
and the data input is written to the memory and mirrored on
the write port input.
Block RAM Characteristics
1. All inputs are registered with the port clock and have a
2. All outputs have a read through or write back function
3. The block RAM are true SRAM memories and do not
4. The ports are completely independent from each other
5. A write operation requires only one clock edge.
6. A read operation requires only one clock edge.
The output ports are latched with a self timed circuit to
guarantee a glitch free read. The state of the output port will
not change until the port executes another read or write
operation.
DS001-2 (v2.8) June 13, 2008
Product Specification
Read Through
Write Back
setup to clock timing specification.
depending on the state of the port WE pin. The outputs
relative to the port clock are available after the
clock-to-out timing specification.
have a combinatorial path from the address to the
output. The LUT cells in the CLBs are still available with
this function.
(i.e., clocking, control, address, read/write function, and
data width) without arbitration.
R
www.xilinx.com
Library Primitives
Figure 31
RAM primitives.
primitives for synthesis and simulation.
Table 11: Available Library Primitives
RAMB4_S1
RAMB4_S1_S1
RAMB4_S1_S2
RAMB4_S1_S4
RAMB4_S1_S8
RAMB4_S1_S16
RAMB4_S2
RAMB4_S2_S2
RAMB4_S2_S4
RAMB4_S2_S8
RAMB4_S2_S16
Figure 32: Single-Port Block RAM Memory
Primitive
Figure 31: Dual-Port Block RAM Memory
Spartan-II FPGA Family: Functional Description
and
Figure 32
WEA
ENA
RSTA
ADDRA[#:0]
DIA[#:0]
WEB
ENB
RSTB
ADDRB[#:0]
DIB[#:0]
CLKA
CLKB
Table 11
WE
EN
RST
ADDR[#:0]
DI[#:0]
CLK
RAMB4_S#_S#
RAMB4_S#
show the two generic library block
describes all of the available
Port A Width
1
2
DO[#:0]
DS001_32_061200
DOA[#:0]
DOB[#:0]
DS001_31_061200
Port B Width
Module 2 of 4
N/A
N/A
16
16
1
2
4
8
2
4
8
32