SL811HS_07 CYPRESS [Cypress Semiconductor], SL811HS_07 Datasheet - Page 25

• Manufacturer Part Number: SL811HS_07
• Description: Embedded USB Host/Slave Controller
• Manufacturer: CYPRESS [Cypress Semiconductor]

Document 38-08008 Rev. *D
DC Characteristics
USB Host Transceiver Characteristics
Every V
capacitor to ensure clean V
at the chip input point (pin) itself.
The best way to do this is to connect a ceramic capacitor
(0.1 μF, 6V) between the pin itself and a good ground. Keep
capacitor leads as short as possible. Use surface mount
Notes
V
V
V
V
I
I
I
C
I
I
I
I
I
V
V
V
V
V
Z
Z
I
13. I
14. I
15. I
16. All typical values are V
17. Z
OH
OL
LL
CC
CCsus1
CCsus2
USB
USBSUS
USB
USBH
USBL
IL
IH
OL
OH
IHYS
USBIH
USBIL
USBOH
USBOL
IN
Parameter
Parameter
static logic level.
[13]
CC
CCsus1
CCsus2
USBX
measurement includes USB Transceiver current (I
[17]
[17]
[14]
[15]
DD
impedance values includes an external resistor of 24 Ohms ± 1% (SL811HS revision 1.2 requires external resistor values of 33 Ohms ±1%).
measured with 12 MHz Clock Input and Internal PLL enabled. Suspend set –(USB transceiver and internal Clocking disabled).
measured with external Clock, PLL disabled, and Suspend set. For absolute minimum current consumption, ensure that all inputs to the device are at
pin, including USB V
Input Voltage LOW
Input Voltage HIGH (5V Tolerant I/O)
Output Voltage LOW (I
Output Voltage HIGH (I
Output Current HIGH
Output Current LOW
Input Leakage
Input Capacitance
Supply Current (V
Supply Current (V
Supply Current (V
Supply Current (V
Transceiver Supply Current in Suspend
Differential
Input Sensitivity (Data+, Data–)
USB Input Voltage HIGH Driven
USB Input Voltage LOW
USB Output Voltage HIGH
USB Output Voltage LOW
Output Impedance HIGH STATE
Output Impedance LOW STATE
Transceiver Supply p-p Current (3.3V)
DD
= 3.3V and T
DD
(free of high frequency noise)
DD
AMB
, must have a decoupling
DD
DD
DD
DD1
= 25°C.
) inc USB @FS
) Suspend w/Clk & Pll Enb
) Suspend no Clk & Pll Dis
)
OL
OH
Description
= 4 mA)
Description
= –4 mA)
USB
) operating at full speed.
capacitors with the shortest traces possible (the use of a
ground plane is strongly recommended).
This product was tested as compliant to the USB-IF specifi-
cation under the test identification number (TID) of 40000689
and is listed on the USB-IF’s integrators list.
36 Ohms
36 Ohms
Min.
0.2V
2.0V
0.8V
2.0V
0.0V
–0.3V
4 mA
4 mA
2.0V
2.4V
Min.
Typ.
4.2 mA
21 mA
50 μA
Typ.
[16]
SL811HS
Page 25 of 32
42 Ohms
42 Ohms
200 mV
25 mA
10 mA
±1 μA
60 μA
10 mA
10 μA
@ FS
10 pF
5 mA
Max.
Max.
0.3V
0.8V
6.0V
0.4V
[+] Feedback
[+] Feedback