ISP1505C NXP [NXP Semiconductors], ISP1505C Datasheet - Page 48
ISP1505C
Manufacturer Part Number
ISP1505C
Description
ULPI Hi-Speed USB host and peripheral transceiver
Manufacturer
NXP [NXP Semiconductors]
Datasheet
1.ISP1505C.pdf
(76 pages)
- Current page: 48 of 76
- Download datasheet (394Kb)
NXP Semiconductors
Table 28.
Table 29.
ISP1505A_ISP1505C_3
Product data sheet
Bit
7
6
5
4
3
2
1
0
Bit
Symbol
Reset
Access
Symbol
USE_EXT_VBUS_
IND
DRV_VBUS_EXT
DRV_VBUS
CHRG_VBUS
DISCHRG_VBUS
DM_PULLDOWN
DP_PULLDOWN
-
OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit description
USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh, S = 0Eh, C = 0Fh) bit
allocation
10.1.5 USB Interrupt Enable Rising Edge register
R/W/S/C
7
0
The bits in this register enable interrupts and RXCMDs to be sent when the corresponding
bits in the USB Interrupt Status register change from logic 0 to logic 1. By default, all
transitions are enabled.
Description
Use External V
0b — Use the internal OTG comparator.
1b — Use the external V
Drive V
0b — Do not drive PSW_N to LOW, disabling V
1b — Drive PSW_N to LOW, enabling V
Drive V
then setting DRV_VBUS is optional.
Charge V
first check that V
DM data lines have been LOW (SE0) for 2 ms.
0b — Do not charge V
1b — Charge V
Discharge V
for an RXCMD indicating that SESS_END has changed from 0 to 1, and then resets this bit to 0
to stop the discharge.
0b — Do not discharge V
1b — Discharge V
DM Pull Down: Enables the 15 k pull-down resistor on DM.
0b — Pull-down resistor is not connected to DM.
1b — Pull-down resistor is connected to DM.
DP Pull Down: Enables the 15 k pull-down resistor on DP.
0b — Pull-down resistor is not connected to DP.
1b — Pull-down resistor is connected to DP.
reserved; writing logic 1 will give undefined results
R/W/S/C
6
0
BUS
BUS
reserved
BUS
: Signals the ISP1505 to drive 5 V on V
External: Controls the external V
BUS
: Charges V
R/W/S/C
BUS
BUS
BUS
: Discharges V
BUS
5
0
.
Indicator: Informs the PHY to use an external V
is discharged (see the DISCHRG_VBUS bit), and that both the DP and
Rev. 03 — 26 August 2008
.
BUS
Table 29
BUS
BUS
BUS
.
R/W/S/C
valid indicator signal input from the FAULT pin.
.
through a resistor. Used for the V
BUS
4
1
shows the bit allocation of the register.
through a resistor. If the link sets this bit to logic 1, it waits
BUS
ULPI HS USB host and peripheral transceiver
R/W/S/C
END_R
SESS_
.
BUS
3
1
ISP1505A; ISP1505C
BUS
supply through the RESET_N/PSW_N pin.
BUS
.
. If DRV_VBUS_EXT is set to logic 1,
VALID_R
R/W/S/C
SESS_
2
1
BUS
pulsing SRP. The link must
BUS
VALID_R
R/W/S/C
VBUS_
overcurrent indicator.
1
1
© NXP B.V. 2008. All rights reserved.
DISCON_R
R/W/S/C
HOST_
0
1
47 of 75
Related parts for ISP1505C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: