FDC37B770 SMSC [SMSC Corporation], FDC37B770 Datasheet - Page 21
FDC37B770
Manufacturer Part Number
FDC37B770
Description
ENHANCED SUPER I/O CONTROLLER WITH WAKE UP FEATURES
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.FDC37B770.pdf
(196 pages)
- Current page: 21 of 196
- Download datasheet (567Kb)
DATA RATE SELECT REGISTER (DSR)
Address 3F4 WRITE ONLY
This register is write only. It is used to program
the data rate, amount of write precompensation,
power down status, and software reset.
data
Configuration Control Register (CCR) not the
DSR,
BIT 0 and 1 DATA RATE SELECT
These bits control the data rate of the floppy
controller.
corresponding to the individual data rates. The
data rate select bits are unaffected by a
software reset, and are set to 250 Kbps after a
hardware reset.
BIT 2 through 4
SELECT
These three bits select the value of write
precompensation that will be applied to the
WDATA output signal.
precompensation values for the combination of
these bits settings.
starting track number to start precompensation.
this starting track number can be changed by
the configure command.
BIT 5 UNDEFINED
Should be written as a logic "0".
BIT 6 LOW POWER
A logic "1" written to this bit will put the floppy
controller into manual low power mode. The
floppy controller clock and data mode after a
software reset or access to the Data Register or
Main Status Register.
rate
RESET
COND.
for
See Table 11 for the settings
is
PC/AT
RESET
S/W
programmed
7
0
Track 0 is the default
PRECOMPENSATION
and
Table 10 shows the
POWER
DOWN
6
0
PS/2
using
5
0
0
Model
The
the
COMP2
PRE-
21
4
0
30 and Microchannel applications.
applications can set the data rate in the DSR.
The data rate of the floppy controller is the most
recent write of either the DSR or CCR. The DSR
is unaffected by a software reset. A hardware
reset
corresponds to the default precompensation
setting and 250 Kbps.
BIT 7 SOFTWARE RESET
This active high bit has the same function as the
DOR RESET (DOR bit 2) except that this bit is
self clearing.
Note: The DSR is Shadowed in the Floppy Data
Rate Select Shadow Register, LD8:CRC2[7:0].
separator circuits will be turned off.
controller will come out of manual low power.
*2Mbps data rate is only available if V
PRECOMP
COMP1
PRE-
Table 8 - Precompensation Delays
will
432
111
001
010
011
100
101
110
000
3
0
set
COMP0
PRE-
the
2
0
PRECOMPENSATION
<2Mbps
Default
Default: See Table 12
125.00
166.67
208.33
250.00
41.67
83.34
0.00
DSR
DRATE
DELAY (nsec)
SEL1
1
1
to
DRATE
SEL0
02H,
2Mbps*
0
0
Default
104.2
20.8
41.7
62.5
83.3
125
0
CC
Other
which
= 5V.
The
Related parts for FDC37B770
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: