MAX809L PHILIPS [NXP Semiconductors], MAX809L Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
MAX809L
Manufacturer Part Number
MAX809L
Description
3-pin microprocessor resets
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.MAX809L.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX809L
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX809L-4.63V
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX809L-EUR
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX809LD
Manufacturer:
NXP
Quantity:
3 000
Part Number:
MAX809LD
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
MAX809LESA+T
Manufacturer:
MAXIM
Quantity:
8 700
Part Number:
MAX809LEUK-T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX809LEUR
Manufacturer:
MAXIN
Quantity:
47 000
Company:
Part Number:
MAX809LEUR+T
Manufacturer:
Maxim
Quantity:
170 015
Company:
Part Number:
MAX809LEUR-T
Manufacturer:
Maxim
Quantity:
5 087
Philips Semiconductors
APPLICATION INFORMATION
Detailed description
A microprocessor reset ensures that the microprocessor starts in a
known and safe state. The reset asserts a reset signal to prevent
code execution errors during power up, power down, or brownout
conditions.
A reset must assert an output within a predictable range of the
supply voltage. The common threshold voltage range is between 5%
and 10% of the nominal supply voltage. MAX809/MAX810 have
4.63 V, 3.08 V and 2.63 V options for 5 V, 3.3 V and 3.0 V supplies
respectively. They have high accuracy (within 3%) that ensures
that the reset thresholds occur within the safe operating range.
Whenever the supply voltage falls below the reset threshold, the
reset signal is asserted. It remains asserted for at least 140 ms after
the supply voltage rises above the threshold. At this point the reset
is released. This delay time helps ensure valid reset signals despite
erratic changes in supply voltage. The MAX809/MAX810 have a
push-pull output stage and do not require a pull-up resistor.
Negative-going V
The MAX809/MAX810 are relatively immune to short negative-going
V
width a negative-going transient can have without causing a reset
signal. As the magnitude of the transient increases below the reset
threshold, the maximum allowable pulse width decreases. Typically,
for the 4.0 V, 4.38 V, and 4.63 V versions of the MAX809/MAX810, a
V
20 s or less will not cause a reset signal. To provide additional
transient rejection, connect a 10 nF bypass capacitor as close as
possible to the V
Ensuring a valid reset output down to V
When V
current (i.e., it becomes open circuit). A high impedance CMOS
logic input connected to RESET can drift to undetermined voltages.
In most applications in which the microprocessor circuitry is
inoperative below 1 V, this will not represent a problem. However, in
applications in which RESET must be valid down to 0 V, use a
2003 Aug 08
CC
CC
3-pin microprocessor resets
Figure 5. Maximum transient duration without causing a
transients and glitches. Figure 5 shows the maximum pulse
transient that goes 100 mV below the reset threshold and lasts
450
400
350
300
250
200
150
100
50
CC
0
reset pulse versus reset comparator overdrive.
1
falls below 1 V, the MAX809 RESET no longer sinks
MAX809/
MAX810R/S/T/Z
CC
RESET COMPARATOR OVERDRIVE, V
pin.
CC
transients
10
MAX809/MAX810J/L/M
100
th
– V
CC
CC
(mV)
= 0 V
SL01728
1000
7
relatively large resistor from RESET to ground as shown in Figure 6.
100 k is small enough to provide a path for any leakage currents to
flow to ground (holding RESET LOW); while it is large enough not to
load RESET. Conversely, a 100 k pull-up resistor is recommended
for MAX810 if RESET is required to remain valid for V
Interfacing to microprocessors with bi-directional
reset pins
Microprocessors with bi-directional reset I/Os, such as the Motorola
68HC11 series, can be connected to the MAX809 RESET output. To
ensure a correct output on the MAX809, even when the
microprocessor reset I/O is in the opposite state, connect a 4.7 k
resistor between the reset pins as shown in Figure 7. This allows the
microprocessor to issue commands to the system regardless of the
state of the RESET. The bi-directional microprocessor reset
functions both as a driven reset input and as an active reset driver.
Figure 7. Interfacing to microprocessor with bi-directional
Figure 6. RESET valid to V
MAX809
MAX809
GND
GND
V
V
CC
CC
RESET
RESET
4.7 k
reset I/O
V
V
100 k
CC
CC
MAX809/MAX810
CC
RESET
RESET
MICROPROCESSOR
= 0 V circuit.
MOTOROLA
68HCxx
GND
GND
V
V
CC
CC
SL01726
SL01727
CC
Product data
< 1 V.