W25Q16CLDAIG WINBOND [Winbond], W25Q16CLDAIG Datasheet - Page 60
W25Q16CLDAIG
Manufacturer Part Number
W25Q16CLDAIG
Description
2.5V 16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
Manufacturer
WINBOND [Winbond]
Datasheet
1.W25Q16CLDAIG.pdf
(77 pages)
- Current page: 60 of 77
- Download datasheet (3Mb)
11.2.38 Program Security Registers (42h)
The Program Security Register instruction is similar to the Page Program instruction. It allows from one
byte to 256 bytes of security register data to be programmed at previously erased (FFh) memory
locations. A Write Enable instruction must be executed before the device will accept the Program Security
Register Instruction (Status Register bit WEL= 1). The instruction is initiated by driving the /CS pin low
then shifting the instruction code “42h” followed by a 24-bit address (A23-A0) and at least one data byte,
into the DI pin. The /CS pin must be held low for the entire length of the instruction while data is being
sent to the device.
The Program Security Register instruction sequence is shown in figure 36. The Security Register Lock
Bits LB[3:1] in the Status Register-2 can be used to OTP protect the security registers. Once a lock bit is
set to 1, the corresponding security register will be permanently locked, Program Security Register
instruction to that register will be ignored (See 11.1.9, 11.2.21 for detail descriptions).
Security Register #1
Security Register #2
Security Register #3
ADDRESS
Instruction (42h)
Figure 36. Program Security Registers Instruction Sequence
A23-16
00h
00h
00h
- 60 -
A15-12
0 0 0 1
0 0 1 0
0 0 1 1
0 0 0 0
0 0 0 0
0 0 0 0
A11-8
W25Q16CL
Byte Address
Byte Address
Byte Address
A7-0
Related parts for W25Q16CLDAIG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
2.5v 16m-bit Serial Flash Memory With Dual And Quad Spi
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
WINBOND I/O, UART, infrared, parallel port, game port, MIDI port, flash ROM interface, general purpose I/O ports, FDC, hardware monitor functions
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
13-MEMORY TONE/PULSE DIALER WITH SAVE FUNCTION
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
TOUCH PULSE DIALER WITH REDIAL
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
Tone/pulse dialer with redial function
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
TOUCH PULSE DIALER WITH REDIAL
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
DTMF Transmitter, 3.58MHz, 5V, Standby, CMOS, 18-PDIP
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
SERIAL VOICE SRAM (128K · 1 BIT)
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
DTMF Transmitter, 3.58MHz, 5V, Standby, CMOS, 18-PDIP
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
13-MEMORY TONE/PULSE DIALER WITH SAVE FUNCTION
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
WE9142ATone/Pulse Telephone Dialer
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
13 Memory Tone / Pulse Switchable Dialer with Save Function
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
14-memory tone/pulse switchable dialer with handfree and lock functions
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
10-memory tone/pulse dialer with save function
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
23-flash memory tone/pulse dialer with handfree, lock and hold functions
Manufacturer:
Winbond
Datasheet: