LPC2220 PHILIPS [NXP Semiconductors], LPC2220 Datasheet - Page 9

• Manufacturer Part Number: LPC2220
• Description: 16/32-bit ARM microcontrollers; flashless with 64 kB, with 10-bit ADC and external memory interface
• Manufacturer: PHILIPS [NXP Semiconductors]

Philips Semiconductors
Table 4:
9397 750 14061
Product data sheet
Symbol
P0.28/AIN1/
CAP0.2/MAT0.2
P0.29/AIN2/
CAP0.3/MAT0.3
P0.30/AIN3/
EINT3/CAP0.0
P1.0 to P1.31
P1.0/CS0
P1.1/OE
P1.16/
TRACEPKT0
P1.17/
TRACEPKT1
P1.18/
TRACEPKT2
P1.19/
TRACEPKT3
P1.20/
TRACESYNC
P1.21/
PIPESTAT0
P1.22/
PIPESTAT1
P1.23/
PIPESTAT2
P1.24/
TRACECLK
P1.25/EXTIN0
Pin description
Pin (LQFP)
25
32
33
91
90
34
24
15
7
102
95
86
82
70
60
[5]
[4]
[4]
[4]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
…continued
Pin (TFBGA) Type
J1
L1
L2
G11
G13
L3
H4
F2
D2
D12
F11
H11
J11
L11
K8
[4]
[4]
[4]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
[5]
I
I
O
I
I
O
I
I
I
I/O
O
O
O
O
O
O
O
O
O
O
O
I
16/32-bit ARM microcontrollers with external memory interface
Rev. 02— 30 May 2005
Description
AIN1 — A/D converter, input 1. This analog input is always
connected to its pin.
CAP0.2 — Capture input for Timer 0, channel 2.
MAT0.2 — Match output for Timer 0, channel 2.
AIN2 — A/D converter, input 2. This analog input is always
connected to its pin.
CAP0.3 — Capture input for Timer 0, Channel 3.
MAT0.3 — Match output for Timer 0, channel 3.
AIN3 — A/D converter, input 3. This analog input is always
connected to its pin.
EINT3 — External interrupt 3 input.
CAP0.0 — Capture input for Timer 0, channel 0.
Port 1: Port 1 is a 32-bit bidirectional I/O port with individual
direction controls for each bit. The operation of port 1 pins
depends upon the pin function selected via the Pin Connect
Block.
Pins 0 through 15 of port 1 are not available.
CS0 — LOW-active Chip Select 0 signal.
OE — LOW-active Output Enable signal.
TRACEPKT0 — Trace Packet, bit 0. Standard I/O port with
internal pull-up.
TRACEPKT1 — Trace Packet, bit 1. Standard I/O port with
internal pull-up.
TRACEPKT2 — Trace Packet, bit 2. Standard I/O port with
internal pull-up.
TRACEPKT3 — Trace Packet, bit 3. Standard I/O port with
internal pull-up.
TRACESYNC — Trace Synchronization. Standard I/O port
with internal pull-up.
Note: LOW on this pin while RESET is LOW, enables pins
P1[25:16] to operate as Trace port after reset.
PIPESTAT0 — Pipeline Status, bit 0. Standard I/O port with
internal pull-up.
PIPESTAT1 — Pipeline Status, bit 1. Standard I/O port with
internal pull-up.
PIPESTAT2 — Pipeline Status, bit 2. Standard I/O port with
internal pull-up.
TRACECLK — Trace Clock. Standard I/O port with internal
pull-up.
EXTIN0 — External Trigger Input. Standard I/O with internal
pull-up.
(Bank 0 addresses range 8000 0000 to 80FF FFFF)
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
LPC2210/2220
9 of 49