V23826-H18-C316 Infineon Technologies, V23826-H18-C316 Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
V23826-H18-C316
Manufacturer Part Number
V23826-H18-C316
Description
Single Mode 622 MBd ATM/SDH/SONET 1x9 Transceiver Extended Temperature Range (40C to 85C)
Manufacturer
Infineon Technologies
Datasheet
1.V23826-H18-C316.pdf
(9 pages)
Pin Description
Regulatory Compliance
Fiber Optics
Pin Name
RxV
RD
RDn
SD
RxV
TxV
TDn
TD
TxV
Feature
Electrostatic
Discharge (ESD)
to the Electrical
Pins
Immunity:
Electrostatic
Discharge (ESD)
to the Duplex SC
Receptacle
Immunity:
Radio Frequency
Electromagnetic
Field
Emission:
Electromagnetic
Interference EMI
CC
EE
EE
CC
Rx Ground
Rx Output
Data
Rx Signal
Detect
Rx 3.3 V
Tx 3.3 V
Tx Input
Data
Tx Ground
Stud Pin
Standard
MIL-STD 883C
Method 3015.4
EN 61000-4-2
IEC 61000-4-2
EN 61000-4-3
IEC 61000-4-3
FCC Class B
EN 55022 Class B
CISPR 22
Level/ Logic
Power Supply
PECL Output
PECL or TTL
Power Supply
PECL Input
Power Supply
Mech. Support S1/2 Not connected
1
2
3
4
6
7
8
9
Pin# Description
5
Comments
Class 1 (>1000 V)
Discharges of ±15kV with
an air discharge probe on
the receptacle cause no
damage.
With a field strength of
3 V/m rms, noise
frequency ranges from
10 MHz to 1 GHz. No
effect on transceiver
performance between the
specification limits.
Noise frequency range:
30 MHz to 6 GHz; Margins
depend on PCB layout and
chassis design
Receiver output
Inverted transmitter
Negative power
supply, normally
ground
data
Inverted receiver
output data
A high level on this
output shows that
optical data is ap-
plied to the optical
input.
Positive power sup-
ply, 3.3 V
input data
Transmitter input
data
Negative power
supply, normally
ground
4
V23826-H18-C316/356/366/376, SM 622MBd ATM/SDH/SONET 1x9 Trx, ext.temp.R.
EYE SAFETY
This laser based single mode transceiver is a Class 1 product. It
complies with IEC 60825-1 and FDA 21 CFR 1040.10 and
1040.11.
To meet laser safety requirements the transceiver shall be oper-
ated within the Absolute Maximum Ratings.
Caution
All adjustments have been made at the factory prior to ship-
ment of the devices. No maintenance or alteration to the
device is required.
Tampering with or modifying the performance of the device
will result in voided product warranty.
Note
Laser Data
Required Labels
Laser Emission
APPLICATION NOTE
ATM transceivers and matching circuits are high frequency
components and shall be terminated as recommended in the
application notes for proper EMI performance. Electromagnetic
emission may be caused by these components.
To prevent emissions it is recommended that cutouts for the
fiber connectors be designed as small as possible.
It is recommended that the Tx plug and the Rx plug be
separated with a bar that divides the duplex SC opening.
Wavelength
Total output power (as defined by IEC: 50 mm
aperture at 10 cm distance)
Total output power (as defined by FDA: 7 mm
aperture at 20 cm distance)
Beam divergence
Failure to adhere to the above restrictions could result in a modifica-
tion that is considered an act of “manufacturing,” and will require,
under law, recertification of the modified product with the U.S. Food
and Drug Administration (ref. 21 CFR 1040.10 (i)).
Indication of laser
aperture and beam
Complies with 21 CFR
1040.10 and 1040.11
FDA
Class 1 Laser Product
IEC
1300 nm
less than
2 mW
less than
180 µW
4°