AM79C960KCW Advanced Micro Devices, AM79C960KCW Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/0/14/advanced_micro_devices_sml.jpg)
AM79C960KCW
Manufacturer Part Number
AM79C960KCW
Description
PCnetTM-ISA Single-Chip Ethernet Controller
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79C960KCW.pdf
(127 pages)
- Current page: 17 of 127
- Download datasheet (815Kb)
LA17-23
Unlatched Address Bus
The unlatched address bus is driven by the PCnet-ISA
controller during bus master cycle.
The functions of these unlatched address pins will
change when GPSI mode is invoked. The table below
shows the pin configuration in GPSI mode. Please refer
to the section on General Purpose Serial Interface for
detailed information on accessing this mode.
MASTER
Master Mode
This signal indicates that the PCnet-ISA controller has
become the Current Master of the ISA bus. After the
PCnet-ISA controller has received a DMA Acknowledge
(DACK) in response to a DMA Request (DRQ), the
Ethernet controller asserts the MASTER signal to indi-
cate to the Permanent Master that the PCnet-ISA
controller is becoming the Current Master.
MEMR
Memory Read
MEMR goes LOW to perform a memory read operation.
MEMW
Memory Write
MEMW goes LOW to perform a memory write
operation.
REF
Memory Refresh
When REF is asserted, a memory refresh is active. The
PCnet-ISA controller uses this signal to mask inadver-
tent DMA Acknowledge assertion during memory
BABL
RCVCCO
JAB
MISS
MERR
MFCO
RINT
IDON
TXSTRT
Number
Pin
10
11
12
5
6
7
9
Bus Master Mode
Pin Function in
Babble
Receive Collision Count Overflow
Jabber
Missed Frame
Memory Error
Missed Frame Count Overflow
Receive Interrupt
Initialization Done
Transmit Start
LA17
LA18
LA19
LA20
LA21
LA22
LA23
Output
Output
Output
Output
Input
Pin Function in
GPSI Mode
SRDCLK
STDCLK
RXCRS
RXDAT
TXDAT
CLSN
TXEN
P R E L I M I N A R Y
Am79C960
refresh periods. If DACK is asserted when REF is ac-
tive, DACK assertion is ignored. REF is monitored to
eliminate a bus arbitration problem observed on some
ISA platforms.
RESET
Reset
When RESET is asserted HIGH the PCnet-ISA control-
ler performs an internal system reset. RESET must be
held for a minimum of 10 XTAL1 periods before being
deasserted. While in a reset state, the PCnet-ISA con-
troller will tristate or deassert all outputs to predefined
reset levels. The PCnet-ISA controller resets itself upon
power-up.
SA0-19
System Address Bus
This bus contains address information, which is stable
during a bus operation, regardless of the source.
SA17-19 contain the same values as the unlatched ad-
dress LA17-19. When the PCnet-ISA controller is the
Current Master, SA0-19 will be driven actively. When
the PCnet-ISA controller is not the Current Master, the
SA0-19 lines are continuously monitored to determine if
an address match exists for I/O slave transfers or Boot
PROM accesses.
SBHE
System Byte High Enable
This signal indicates the high byte of the system data
bus is to be used. SBHE is driven by the PCnet-ISA con-
troller when performing bus mastering operations.
SD0-15
System Data Bus
These pins are used to transfer data to and from the
PCnet-ISA controller to system resources via the ISA
data bus. SD0-15 is driven by the PCnet-ISA controller
when performing bus master writes and slave read op-
erations. Likewise, the data on SD0-15 is latched by the
PCnet-ISA controller when performing bus master
reads and slave write operations.
SMEMR
System Memory Read
This pin is used during Boot PROM access. The Boot
PROM can be disabled by not connecting this pin.
Board Interface
APCS
Address PROM Chip Select
This signal is asserted when the external Address
PROM is read. When an I/O read operation is per-
formed on the first 16 bytes in the PCnet-ISA controller’s
I/O space, APCS is asserted. The outputs of the exter-
nal Address PROM drive the PROM Data Bus. The
PCnet-ISA controller buffers the contents of the PROM
data bus and drives them on the lower eight bits of the
System Data Bus.
Input
Input/Output
Input/Output
Input/Output
Input
Output
AMD
1-359
Related parts for AM79C960KCW
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AM27S29DC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Advanced Micro Devices [4,096-Bit (512x8) Bipolar PROM]
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM27S29APC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Advanced Micro Devices [4,096-Bit (512x8) Bipolar PROM]
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM29BL802CB-70RZE](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Advanced Micro Devices [8 Megabit (512 K x 16-Bit) CMOS 3.0 Volt-only Burst Mode Flash Memory]
Manufacturer:
Advanced Micro Devices
Datasheet:
![M41000001Y](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
M41000001YAdvanced Micro Devices [32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory and 4 Mbit (512 K x 8-Bit/256 K x 16-Bit) Static RAM]
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM95C94JC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Advanced Burst Error Processor
Manufacturer:
Advanced Micro Devices
![AM7992BPC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Serial interface adapter (SIA)
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM9519ADC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Universal interrupt controller
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM27C256-150DC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
256 kilobit CMOS EPROM
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM9128-10PC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
2048 x 8 static RAM, 100ns
Manufacturer:
Advanced Micro Devices
Datasheet:
![P8284A](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Manufacturer:
Advanced Micro Devices
Datasheet:
![DM81LS98N](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
![AM2966PC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AM2966PCOctal Dynamic Memory Drivers with Three-State Outputs
Manufacturer:
Advanced Micro Devices
Datasheet:
![DM81LS97N](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
![DM81LS96N](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
![PAL16L8-7PC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
TTL programmable array logic, 7ns
Manufacturer:
Advanced Micro Devices
Datasheet: