EVAL-AD7843CB3 AD [Analog Devices], EVAL-AD7843CB3 Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
EVAL-AD7843CB3
Manufacturer Part Number
EVAL-AD7843CB3
Description
Touch Screen Digitizer
Manufacturer
AD [Analog Devices]
Datasheet
1.EVAL-AD7843CB3.pdf
(16 pages)
Sixteen Clocks per Cycle
The control bits for the next conversion can be overlapped with
the current conversion to allow for a conversion every 16 DCLK
cycles, as shown in Figure 11. This timing diagram also allows
for the possibility of communication with other serial peripherals
between each (eight DCLK) byte transfer between the processor
and the converter. However, the conversion must be complete
within a short enough time frame to avoid capacitive droop
effects which may distort the conversion result. It should also
be noted that the AD7843 will be fully powered while other
serial communications may be taking place between byte transfers.
Fifteen Clocks per Cycle
Figure 12 shows the fastest way to clock the AD7843. This
scheme will not work with most microcontrollers or DSPs as in
general they are not capable of generating a 15-clock cycle per
serial transfer. However, some DSPs will allow the number of
clocks per cycle to be programmed and this method could also
be used with FPGAs (Field Programmable Gate Arrays) or
ASICs (Application Specific Integrated Circuits). As in the 16-
clocks-per-cycle case, the control bits for the next conversion
are overlapped with the current conversion to allow for a con-
version every 15 DCLK cycles, using 12 DCLKs to perform
the conversion and three DCLKs to acquire the analog input.
DCLK
BUSY
DOUT
AD7843
DIN
CS
DOUT
DCLK
BUSY
DIN
CS
S
1
A2
S
1
A1
A0
CONTROL BITS
MODE
SER/
DFR
PD1 PD0
8
11
10
1
11
9
10
8
9
7
8
6
15
7
S
This will effectively increase the throughput rate of the AD7843
beyond that used for the specifications which are tested using 16
DCLKs per cycle, and DCLK = 2 MHz.
8-Bit Conversion
The AD7843 can be set up to operate in an 8-bit rather than
12-bit mode, by setting the MODE bit to 1 in the control regis-
ter. This mode allows a faster throughput rate to be achieved,
assuming 8-bit resolution is sufficient. When using the 8-bit
mode a conversion is complete four clock cycles earlier than in
the 12-bit mode. This could be used with serial interfaces that
provide 12 clock transfers, or two conversions could be com-
pleted with three eight-clock transfers. The throughput rate will
increase by 25% as a result of the shorter conversion cycle, but
the conversion itself can occur at a faster clock rate because the
internal settling time of the AD7843 is not as critical because
settling to 8 bits is all that is required. The clock rate can be as
much as 50% faster. The faster clock rate and fewer clock cycles
combine to provide double the conversion rate.
PEN INTERRUPT REQUEST
The pen interrupt equivalent output circuitry is outlined in
Figure 13. By connecting a pull-up resistor (10 kΩ to 100 kΩ)
between V
PENIRQ output will remain high normally. If PENIRQ has
5
1
A2
6
4
5
A1
3
8
CC
A0
4
2
S
and this CMOS Logic open drain output, the
1
MODE
1
3
SER/
DFR
0
2
CONTROL BITS
PD1 PD0
1
0
11
10
8
9
1
8
11
7
10
6
15
9
S
5
1
A2
4