82V3001 IDT [Integrated Device Technology], 82V3001 Datasheet - Page 12
![no-image](/images/no-image-200.jpg)
82V3001
Manufacturer Part Number
82V3001
Description
WAN PLL WITH SINGLE REFERENCE INPUT
Manufacturer
IDT [Integrated Device Technology]
Datasheet
1.82V3001.pdf
(27 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
82V3001APVG
Manufacturer:
IDT
Quantity:
20 000
IDT82V3001A WAN PLL WITH SINGLE REFERENCE INPUT
3.1.4
required, or a system is just powered up and the network
synchronization has not been achieved.
synchronization signals which are based on the master clock frequency
(OSCi) only and not synchronized to the input reference signal.
master clock (OSCi). So if a ±32 ppm output clock is required, the
master clock must also be ±32 ppm. Refer to
information.
Freerun Mode.
3.2
operates on its falling edge. The input reference can be 8 kHz, 1.544
MHz or 2.048 MHz. As shown in
determine which of the three frequencies is selected. Every time the
frequency is changed, the device must be reset to make the change
effective.
Table - 3 Input Reference Frequency Selection
Generation circuit when it is enabled manually or automatically (by the
TIE_en pin or TIE auto-enable logic generated by the State Control
Circuit).
(current output feedback from the Frequency Select Circuit) by the
Measure Circuit. The phase difference between the input reference and
the feedback signal is sent to the Storage Circuit for TIE correction. The
Freerun Mode is typically used when a master clock source is
In Freerun Mode, the IDT82V3001A provides timing and
The accuracy of the output clock is equal to the accuracy of the
The FREERUN pin will go high whenever the IDT82V3001A works in
The IDT82V3001A accepts one reference input signal, Fref, and
The TIE Control Block will work under the control of the Step
The input reference signal is compared with the feedback signal
F_sel1
0
0
1
1
Feedback
signal
TIE_en
Fref
FREERUN MODE
FREQUENCY SELECT CIRCUIT
F_sel0
0
1
0
1
Table -
3, the F_sel1 and F_sel0 pins
Measure
Input Frequency
"OSC"
Circuit
1.544 MHz
2.048 MHz
Reserved
8 kHz
Figure - 5 TIE Control Circuit Diagram
section for more
Step Generation
12
Storage
3.3
IDT82V3001A. The IDT82V3001A will automatically enter Holdover
Mode (Auto-Holdover) if the incoming reference signal is out of the
capture range (See
reference, or a large frequency shift in the input reference. When the
input reference returns to normal, the DPLL will return to Normal Mode.
In Holdover Mode, the output signal of the IDT82V3001A is based on
the output signal 30 ms to 60 ms prior to entering Holdover Mode. The
amount of phase drift in Holdover Mode is negligible because Holdover
Mode is very accurate (e.g., 0.025 ppm). Consequently, the phase delay
between the input and output after switching back to Normal Mode is
preserved.
3.4
use the reference generated by the storage techniques instead. But
when switching the operation mode, a step change in phase on the input
reference will occur. And a step change in phase at the input of the
DPLL would lead to unacceptable phase changes in the output signals.
The TIE control block, when enabled, prevents a step change in phase
on the input reference signals from causing a step change in phase at
the output of the DPLL block.
diagram.
Circuit
Trigger Circuit generates a virtual reference with the phase corrected to
the same position as the previous reference according to the value
stored in the Storage Circuit. With this TIE correction mechanism, the
reference is switched without generating a step change in phase.
switch is performed with the TIE Control Block enabled.
TCLR
This circuit monitors the input reference signal into the
If the current reference is badly damaged or lost, it is necessary to
Figure - 6
INVALID INPUT SIGNAL DETECTION
TIE CONTROL BLOCK
shows the phase transient that would result if a state
Table -
Trigger Circuit
INDUSTRIAL TEMPERATURE RANGE
7), including a complete loss of input
Figure - 5
shows the TIE Control Block
Reference
Virtual
Signal