EMC6D103_07 SMSC [SMSC Corporation], EMC6D103_07 Datasheet - Page 60
EMC6D103_07
Manufacturer Part Number
EMC6D103_07
Description
Fan Control Device with High Frequency PWM Support and Hardware Monitoring Features
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.EMC6D103_07.pdf
(92 pages)
- Current page: 60 of 92
- Download datasheet (2Mb)
Revision 0.3 (03-01-07)
BIT
4-7
0
1
2
3
Reserved
READY
START
OVRID
NAME
LOCK
Note: There is a start-up time of up to 82ms for monitoring after the start bit is set to ‘1’, during which
The following summarizes the operation of the part based on the Start bit:
1. If Start bit = '0' then:
s. Fans are set to Full On.
t.
u. No Status bits are set.
2. If Start bit = '1'
v. All fan control and monitoring will be based on the current values in the registers. There is no need
w. Status bits may be set.
x. Setting the START bit to 1 does not prevent the limit and parameter registers from being written.
Note: Once programmed, the register values will be saved when start bit is reset to ‘0’.
No voltage, temperature, or fan tach monitoring is performed. The values in the reading registers
will be N/A (Not Applicable), which means these values will not be considered valid readings until
the Start bit = '1'. The exception to this is the Tachometer reading registers, which always give the
actual reading on the TACH pins.
to preserve the default values after software has programmed these registers because no
monitoring or auto fan control will be done when Start bit = '0'.
time the reading registers are not valid.
R/W
R/W
R/W
R/W
R
R
DEFAULT
0
0
0
0
0
Fan Control Device with High Frequency PWM Support and Hardware Monitoring Features
Table 8.14 Ready/Lock/Start Monitoring
When software writes a 1 to this bit, the EMC6D103 enables
monitoring and PWM output control functions based on the limit and
parameter registers. Before this bit is set, the part does not update
register values. Whenever this bit is set to 0, the monitoring and PWM
output control functions are based on the default limits and
parameters, regardless of the current values in the limit and parameter
registers. The EMC6D103 preserves the values currently stored in the
limit and parameter registers when this bit is set or cleared. This bit is
not affected by setting the Lock bit.
Note:
Setting this bit to 1 locks specified limit and parameter registers. Once
this bit is set, limit and parameter registers become read only and will
remain locked until the device is powered off. This register bit
becomes read only once it is set.
The EMC6D103 sets this bit automatically after the part is fully
powered up, has completed the power-up-reset process, and after all
A/D converters are functioning (all bias conditions for the A/Ds have
stabilized and the A/Ds are in operational mode). (Always reads back
‘1’.)
If this bit is set to 1, all PWM outputs go to 100% duty cycle regardless
of whether or not the lock bit is set.
Reserved.
DATASHEET
When this bit is 0, all fans are on full 100% duty cycle, i.e.,
PWM pins are high for 255 clocks, low for 1 clock. When this
bit is 0, the part is not monitoring.
60
DESCRIPTION
SMSC EMC6D103
Datasheet
Related parts for EMC6D103_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: