LPC1114FBD48/323,1 NXP Semiconductors, LPC1114FBD48/323,1 Datasheet - Page 45
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
LPC1114FBD48/323,1
Manufacturer Part Number
LPC1114FBD48/323,1
Description
ARM Microcontrollers - MCU Cortex-M0 32 kB Fl 8 kB SRAM
Manufacturer
NXP Semiconductors
Datasheet
1.LPC1114FN2810212.pdf
(114 pages)
Specifications of LPC1114FBD48/323,1
Rohs
yes
Core
ARM Cortex M0
Processor Series
LPC1114
Data Bus Width
32 bit
Maximum Clock Frequency
50 MHz
Program Memory Size
32 KB
Data Ram Size
8 KB
On-chip Adc
Yes
Operating Supply Voltage
1.8 V to 3.6 V
Operating Temperature Range
- 65 C to + 150 C
Package / Case
HVQFN-33
Mounting Style
SMD/SMT
Factory Pack Quantity
250
NXP Semiconductors
LPC111X
Product data sheet
7.5.2 Interrupt sources
7.7.1 Features
7.6 IOCONFIG block
7.7 Fast general purpose parallel I/O
Each peripheral device has one interrupt line connected to the NVIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any GPIO pin (total of up to 42 pins) regardless of the selected function, can be
programmed to generate an interrupt on a level, or rising edge or falling edge, or both.
The IOCONFIG block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on-chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Multiple outputs
can be set or cleared in one write operation.
LPC1110/11/12/13/14/15 use accelerated GPIO functions:
Additionally, any GPIO pin (total of up to 42 pins) providing a digital function can be
programmed to generate an interrupt on a level, a rising or falling edge, or both.
•
•
•
•
•
•
•
•
•
•
In the LPC1110/11/12/13/14/15, the NVIC supports 32 vectored interrupts including up
to 13 inputs to the start logic from individual GPIO pins.
Four programmable interrupt priority levels with hardware priority level masking.
Software interrupt generation.
GPIO registers are a dedicated AHB peripheral so that the fastest possible I/O timing
can be achieved.
Entire port value can be written in one instruction.
Bit level port registers allow a single instruction to set or clear any number of bits in
one write operation.
Direction control of individual bits.
All I/O default to inputs with pull-ups enabled after reset with the exception of the
I
Pull-up/pull-down resistor configuration can be programmed through the IOCONFIG
block for each GPIO pin (except for pins PIO0_4 and PIO0_5).
On the LPC1100, all GPIO pins (except PIO0_4 and PIO0_5) are pulled up to 2.6 V
(V
2
C-bus pins PIO0_4 and PIO0_5.
DD
= 3.3 V) if their pull-up resistor is enabled in the IOCONFIG block.
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 20 February 2013
LPC1110/11/12/13/14/15
32-bit ARM Cortex-M0 microcontroller
© NXP B.V. 2013. All rights reserved.
45 of 114