PCAL9535APW,118 NXP Semiconductors, PCAL9535APW,118 Datasheet - Page 20

• Manufacturer Part Number: PCAL9535APW,118
• Description: Interface - I/O Expanders 16bit I2C IO Port Interrupt and Agile
• Manufacturer: NXP Semiconductors

Specifications of PCAL9535APW,118

• Maximum Operating Frequency: 100 kHz
• Operating Supply Voltage: 1.65 V to 5.5 V
• Operating Temperature Range: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Package / Case: TSSOP-24
• Operating Current: 160 mA
• Output Current: 25 mA
• Power Dissipation: 200 mW
• Product Type: I/O Expanders

NXP Semiconductors
8. Application design-in information
PCAL9535A
Product data sheet
Fig 13. Typical application
(3.3 V)
(1) External resistors are required for inputs (on P port) that may float. Also, internal pull-up or pull-down may be used to eliminate
V
DD
Device address configured as 0100 000X for this example.
P0_0, P0_2, P0_3 configured as outputs.
P0_1, P0_4, P0_5 configured as inputs.
P0_6, P0_7 and (P1_0 to P1_7) configured as inputs.
the need for external components. If a driver to an input will never let the input float, a resistor is not needed. If an output in the
P port is configured as a push-pull output there is no need for external pull-up resistors. If an output in the P port is configured
as an open-drain output, external pull-up resistors are required.
CONTROLLER
MASTER
V
V
DD
SS
8.1 Minimizing I
SDA
SCL
INT
When the I/Os are used to control LEDs, they are normally connected to V
resistor as shown in
V
than V
Designs needing to minimize current consumption, such as battery power applications,
should consider maintaining the I/O pins greater than or equal to V
Figure 14
than the LED supply voltage by at least 1.2 V. Both of these methods maintain the I/O V
at or above V
I
is about 1.2 V less than V
10 kΩ
DD
.
shows a high value resistor in parallel with the LED.
10 kΩ
DD
DD
All information provided in this document is subject to legal disclaimers.
and prevents additional supply current consumption when the LED is off.
10 kΩ
when the I/Os are used to control LEDs
Figure
Rev. 1 — 28 September 2012
Low-voltage 16-bit I
SCL
SDA
INT
A2
A1
A0
PCAL9535A
13. Since the LED acts as a diode, when the LED is off the I/O
V
V
DD
DD
SS
. The supply current, I
P0_0
P0_1
P0_2
P0_3
P0_4
P0_5
P0_6
P0_7
P1_0
P1_1
P1_2
P1_3
P1_4
P1_5
P1_6
P1_7
2 kΩ
NUMERIC
10 DIGIT
KEYPAD
2
C-bus I/O port with interrupt and Agile I/O
100 kΩ
(×3)
DD
, increases as V
enable
Figure 15
PCAL9535A
DD
INT
RESET
(e.g., alarm system)
ALARM
SUB-SYSTEM 1
(e.g., temp sensor)
SUB-SYSTEM 3
A
B
SUB-SYSTEM 2
(e.g., counter)
when the LED is off.
© NXP B.V. 2012. All rights reserved.
I
controlled
switch
(e.g., CBT device)
becomes lower
shows V
DD
002aah430
through a
(1)
(1)
V
DD
DD
20 of 46
less
I