SCC2681AE1A44-T NXP Semiconductors, SCC2681AE1A44-T Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
SCC2681AE1A44-T
Manufacturer Part Number
SCC2681AE1A44-T
Description
UART Interface IC RPLACMNT FOR SCN2681
Manufacturer
NXP Semiconductors
Type
Dual asynchronous receiver/transmitter (DUART)r
Datasheet
1.SCC2681AE1A44-S.pdf
(29 pages)
Specifications of SCC2681AE1A44-T
Product Category
UART Interface IC
Rohs
yes
Number Of Channels
2
Data Rate
115.2 Kbps
Supply Voltage - Max
5.5 V
Supply Voltage - Min
4.5 V
Supply Current
10 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Package / Case
PLCC-44
Mounting Style
SMD/SMT
Operating Supply Voltage
5 V
Factory Pack Quantity
500
Part # Aliases
SCC2681AE1A44,518
the underrun condition, the issuing of the transmitter disable must be
Philips Semiconductors
or transmitted character. Likewise, if a mode is deselected the
device will switch out of the mode immediately. An exception to this
is switching out of autoecho or remote loopback modes: if the
deselection occurs just after the receiver has sampled the stop bit
(indicated in autoecho by assertion of RxRDY), and the transmitter
is enabled, the transmitter will remain in autoecho mode until the
entire stop has been retransmitted.
MR2A[5] – Channel A Transmitter Request-to-Send Control
CAUTION: When the transmitter controls the OP pin (usually used
for the RTSN signal) the meaning of the pin is not RTSN at all!
Rather, it signals that the transmitter has finished the transmission
(i.e., end of block).
Note: Please see Application Note AN10251 for more information
on this subject.
This bit allows deactivation of the RTSN output by the transmitter.
This output is manually asserted and negated by the appropriate
commands issued via the SOPR and ROPR registers. MR2[5] set to
1 caused the RTSN to be reset automatically one bit time after the
character(s) in the transmit shift register and in the THR (if any) are
completely transmitted (including the programmed number of stop
bits) if a previously issued transmitter disable is pending. This
feature can be used to automatically terminate the transmission as
follows:
1. Program the auto-reset mode: MR2[5]=1
2. Enable transmitter, if not already enabled
3. Set OPR[0] or OPR[1] to ‘1’ via the SOPR and ROPR registers
4. Send message
5. After the last character of the message is loaded to the THR,
6. The last character will be transmitted and the RTSN will be reset
NOTE: The transmitter is in an underrun condition when both the
TxRDY and the TxEMT bits are set. This condition also exists
immediately after the transmitter is enabled from the disabled or
reset state. When using the above procedure with the transmitter in
delayed from the loading of a single, or last, character until the
TxRDY becomes active again after the character is loaded.
MR2A[4] – Channel A Clear-to-Send Control
If this bit is 0, CTSAN has no effect on the transmitter. If this bit is a
1, the transmitter checks the state of CTSAN (IPO) each time it is
ready to send a character. If IPO is asserted (LOW), the character is
transmitted. If it is negated (HIGH), the TxDA output remains in the
marking state and the transmission is delayed until CTSAN goes
LOW. Changes in CTSAN while a character is being transmitted do
not affect the transmission of that character..
MR2A[3:0] – Channel A Stop Bit Length Select
This field programs the length of the stop bit appended to the
transmitted character. Stop bit lengths of .563 TO 1 AND .563 to 2
bits. In increments of 0.625 bit, can be programmed for character
lengths of 6, 7, and 8 bits. For a character lengths of 5 bits, 1.0625
to 2 stop bits can be programmed in increments of .0625 bit.
The receiver only checks for a ‘mark’ condition at the center of the
first stop bit position (one bit time after the last data bit, or after the
parity bit is enabled) in all cases.
If an external 1 clock is used for the transmitter, MR2A[3] = 0
selects one stop bit and MR2A[3] = 1 selects two stop bits to be
transmitted.
2004 Apr 06
Dual asynchronous receiver/transmitter (DUART)
disable the transmitter. (If the transmitter is underrun, a special
case exists. See note below.)
one bit time after the last stop bit is sent.
15
applied via CRB. After reading or writing MR1B, the pointer will point
MR1B – Channel B Mode Register 1
MR1B is accessed when the Channel B MR pointer points to MR1.
The pointer is set to MR1 by RESET or by a ‘set pointer’ command
to MR2B.
MR2B – Channel B Mode Register 2
MR2B is accessed when the Channel B MR pointer points to MR2,
which occurs after any access to MR1B. Accesses to MR2B do not
change the pointer.
The bit definitions for mode registers 1 and 2 are identical to the bit
definitions for MRA and MR2A except that all control actions apply
to the Channel B receiver and transmitter and the corresponding
inputs and outputs.
CSRA – Channel A Clock Select Register
STandard baud rates are shown below. A read at address 0x2
changes the baud rate generator to give higher speed baud rates.
(See Table 5 on page 21.) A subsequent read at address 0x2
changes the baud rate generator back to standard rates. In other
words, each read at 0x2 toggles the controlling flip-flop.
Table 3. Bit Rate Generator Characteristics
NOTE: Duty cycle of 16 clock is 50%
Asynchronous UART communications can tolerate frequency error
of 4.1% to 6.7% in a “clean” communications channel. The percent
of error changes as the character length changes. The above
percentages range from 5 bits not parity to 8 bits with parity and one
stop bit. The error with 8 bits not parity and one stop bit is 4.6%. If a
stop bit length of 9/16 is used, the error tolerance will approach 0
due to a variable error of up to 1/16 bit time in receiver clock phase
alignment to the start bit.
Normal rate (baud)
115.2 k
14.4 k
19.2 k
28.8 k
38.4 k
57.6 k
134.5
1050
1200
1800
2000
2400
4800
7200
9600
150
200
300
600
110
50
75
Crystal or Clock = 3.6864MHz
Actual 16 clock
1843.2 k
16.756
32.056
1.759
2.153
153.6
230.4
307.2
460.8
614.4
921.6
(kHz)
115.2
19.2
28.8
38.4
76.8
0.8
1.2
2.4
3.2
4.8
9.6
1%.
SCC2681
Error (%)
–0.069
–0.260
Product data
0.059
0.175
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0