73S1217F-68MR/F/PE Maxim Integrated, 73S1217F-68MR/F/PE Datasheet - Page 76
73S1217F-68MR/F/PE
Manufacturer Part Number
73S1217F-68MR/F/PE
Description
8-bit Microcontrollers - MCU
Manufacturer
Maxim Integrated
Datasheet
1.73S1217F-68MRFPE.pdf
(140 pages)
Specifications of 73S1217F-68MR/F/PE
Rohs
yes
Core
80515
Data Bus Width
8 bit
Part # Aliases
90-W1217+TF5
- Current page: 76 of 140
- Download datasheet (942Kb)
D- signals to provide the proper impedance matching on these pins.
The USB peripheral block is not able to support read or write operations to the USB SFR registers when
the MPU clock is running at MPU clock rates of 12MHz or greater. In order to properly communicate with
the USB SFR registers when running at these speeds, wait states must be inserted when addressing the
USB SFRs. The CKCON register allows wait states to be inserted when accessing these registers. The
proper settings for the number of wait states are shown in Error! Reference source not found..
Changing these parameters while the USB interface is active may cause communication errors on
the USB interface.
decoding, handshake packet generation, Data0/Data1 toggle synchronization, bit stuffing, bus idle
detection and other protocol generation/checking required in Chapter 8 of the USB specification.
The firmware is responsible for servicing and building the messages required under Chapter 9 of the USB
specification. Device configuration is stored in the firmware. Data received from the USB port is stored in
the appropriate IN FIFO that is read by the firmware and processed. The messages to be sent back to
the USB host are generated by firmware and placed back into the appropriate OUT FIFO. Stall/NAK
handshakes are generated as appropriate if the RAM is not available for another message from the USB
host. Suspend and resume modes are supported. All register/FIFO spaces are located in Data Memory
space. The FIFOs are dedicated for USB storage and are unused in a configuration that is not using
USB. All registers in the USB interface are located in external data memory address (XRAM) space
starting at address FC00’h.
1.7.16.1
The 73S1217F Application Programming Interface includes some dedicated software commands to
configure the USB interface, to get a status of each USB Endpoint, to stall / unstall portions of the USB,
and to send / receive data to / from each endpoint.
USB API entirely manages the USB circuitry, the USB registers and the FIFOs. Use of those commands
facilitates USB implementation, without dealing with low-level programming.
Miscellaneous Control Register 1 (MISCtl1): 0xFFF2
Note: When using the USB on the 73S1217F, external 24Ω series resistors must be added to the D+ and
76
MISCtl1.7
MISCtl1.6
MISCtl1.5
MISCtl1.4
MISCtl1.3
MISCtl1.2
MISCtl1.1
MISCtl1.0
MSB
Bit
When changing the MPU clock rate or the number of wait states, the USB connection
must be inactive. If the USB is active, then it must be inactivated before changing the
MPU clock or number of wait states. It can then be reconnected and re-enumerated.
USB Interface Implementation
–
USBCON
ANAPEN
USBPEN
Symbol
FLSH66
FRPEN
–
–
–
–
FRPEN
Flash Read Pulse enable.
Flash Read Pulse.
Analog power enable.
0 = Enable the USB differential transceiver.
1 = Connect pull-up resistor from VDD to D+. If connected, the USB host
will recognize the attachment of a USB device and begin enumeration.
Table 77: The MISCtl1 Register
FLSH66
–
0x10
ANAPEN USBPEN USBCON
Function
LSB
Rev. 1.2
Related parts for 73S1217F-68MR/F/PE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC SMART CARD READER 68-QFN
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
IC SMART CARD READER PROG 68-QFN
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
IC SMART CARD READER PROG 68-QFN
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
IC SMART CARD READER 68-QFN
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
The Teridian 73S1217F is a self-contained SoC smart card reader IC that is an ideal solution for any USB-connected ISO 7816 design
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Development Boards & Kits - 8051 73S1217F Eval Brd (Usb Cable, Doc. Cd)
Manufacturer:
Maxim Integrated
Part Number:
Description:
BOARD EVAL 73S1217F CBL/DOC/CD
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Power Management Modules & Development Tools 73S1217F DEV KIT EVALBD ICE USBCBL CD
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
MCU, MPU & DSP Development Tools 73S1217F EVAL BRD EVAL BD USB CBL CD
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Microcontrollers (MCU)
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet: