S9S08DZ60F2MLF Freescale Semiconductor, S9S08DZ60F2MLF Datasheet - Page 88

• Manufacturer Part Number: S9S08DZ60F2MLF
• Description: 8-bit Microcontrollers - MCU M74K MASK ONLY-AUTO
• Manufacturer: Freescale Semiconductor

Specifications of S9S08DZ60F2MLF

• Rohs: yes
• Core: HCS08
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Program Memory Size: 60 KB
• Data Ram Size: 4 K
• On-chip Adc: Yes
• Operating Supply Voltage: 2.7 V to 5.5 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-48
• Mounting Style: SMD/SMT
• Processor Series: MC9S08DZ60

Chapter 6 Parallel Input/Output Control
6.3.2
A valid edge or level on an enabled port pin will set PTxIF in PTxSC. If PTxIE in PTxSC is set, an interrupt
request will be presented to the CPU. Clearing of PTxIF is accomplished by writing a 1 to PTxACK in
PTxSC provided all enabled port inputs are at their deasserted levels. PTxIF will remain set if any enabled
port pin is asserted while attempting to clear by writing a 1 to PTxACK.
6.3.3
The port interrupt pins can be configured to use an internal pull-up/pull-down resistor using the associated
I/O port pull-up enable register. If an internal resistor is enabled, the PTxES register is used to select
whether the resistor is a pull-up (PTxESn = 0) or a pull-down (PTxESn = 1).
6.3.4
When an interrupt pin is first enabled, it is possible to get a false interrupt flag. To prevent a false interrupt
request during pin interrupt initialization, the user should do the following:
6.4
Pin behavior following execution of a STOP instruction depends on the stop mode that is entered. An
explanation of pin behavior for the various stop modes follows:
88
1. Mask interrupts by clearing PTxIE in PTxSC.
2. Select the pin polarity by setting the appropriate PTxESn bits in PTxES.
3. If using internal pull-up/pull-down device, configure the associated pull enable bits in PTxPE.
4. Enable the interrupt pins by setting the appropriate PTxPSn bits in PTxPS.
5. Write to PTxACK in PTxSC to clear any false interrupts.
6. Set PTxIE in PTxSC to enable interrupts.
•
•
Stop2 mode is a partial power-down mode, whereby I/O latches are maintained in their state as
before the STOP instruction was executed. CPU register status and the state of I/O registers should
be saved in RAM before the STOP instruction is executed to place the MCU in stop2 mode. Upon
recovery from stop2 mode, before accessing any I/O, the user should examine the state of the PPDF
bit in the SPMSC2 register. If the PPDF bit is 0, I/O must be initialized as if a power on reset had
occurred. If the PPDF bit is 1, peripherals may require initialization to be restored to their pre-stop
condition. This can be done using data previously stored in RAM if it was saved before the STOP
instruction was executed. The user must then write a 1 to the PPDACK bit in the SPMSC2 register.
Access to I/O is now permitted again in the user application program.
In stop3 mode, all I/O is maintained because internal logic circuity stays powered up. Upon
recovery, normal I/O function is available to the user.
Pin Behavior in Stop Modes
Edge and Level Sensitivity
Pull-up/Pull-down Resistors
Pin Interrupt Initialization
MC9S08DZ60 Series Data Sheet, Rev. 4
Freescale Semiconductor