KIT34708VMEVBE Freescale Semiconductor, KIT34708VMEVBE Datasheet - Page 18

• Manufacturer Part Number: KIT34708VMEVBE
• Description: Acceleration Sensor Development Tools 13x13 PWR MGMT AND UI
• Manufacturer: Freescale Semiconductor

Specifications of KIT34708VMEVBE

• Rohs: yes
• Tool Is For Evaluation Of: MC34708
• Sensing Axis: Single Axis
• Interface Type: I2C, SPI, USB
• Operating Voltage: 5 V
• Operating Current: 5 A
• Output Type: Analog, Digital

Table 6. KIT34708VMEVBE (Rev. B) Unpopulated Jumper Description Key
Freescale Semiconductor
Reference
J40 - J44
Jumper
J39
J45
J46
J47
J50
J51
J52
J53
J54
J55
J56
J75
J74
J73
Power good signal for SW2
Power good signal for SW1
VINREFDDR input voltage
PUMS 1 configuration
PUMS 2 configuration
PUMS 3 configuration
General Description
VUSB2 external PNP
GPIOLV0/STANDBY
SWBST enablement
CLK32KVCC supply
SW1 configuration
SW4 configuration
SW4A to SPIVCC
GPIOVDD supply
UID resistance
/INT selection
configuration
configuration
enablement
enablement
selection
selection
KIT34708VMEVBE Evaluation
Position
Shorted
Shorted
Shorted
Open
Open
Open
Open
1-2
3-4
1-2
3-4
1-2
2-3
1-2
2-3
1-2
2-3
1-2
3-4
5-6
1-2
3-4
5-6
1-2
2-3
1-2
2-3
1-2
2-3
1-2
2-3
No 5.0 V power reference to the resistor divider for ADIN9, ADIN10, ADIN11
voltage measurements
5.0 V power reference to the resistor divider for ADIN9, ADIN10, ADIN11 voltage
measurements
Different jumper configurations for manually testing the ID resistance value
assignments
Connects the GPIOLV0 pin to the J11 connector for monitor/control
Connects the STANDBY pin to the J11 connector for monitor/control
Connects the SW2PWGD pin to the J11 connector for monitoring
Connects the INT pin to the J11 connector for monitoring
No connection of the SW1PWGD pin to the J11 connector for monitoring
Connects the SW1PWGD pin to the J11 connector for monitoring
Connects SW1CFG to VCOREDIG for single phase
Connects SW1CFD to ground for dual phase
GPIOVDD is supplied by SW3
GPIOVDD is supplied by SW5
SPIVCC not supplied by SW4A
SPIVCC is supplied by SW4A
Input to the integrated PMOS pass FET for lower current requirements on
VUSB2
Base current drive pin for the external PNP when higher currents are required
from VUSB2
Connects SW4CFG to VCOREDIG for single phase mode
Connects SW4CFD to VCORE for dual phase mode
Connects SW4CFD to ground for separate independent output mode
VINREFDDR is supplied by SW4A
VINREFDDR is supplied by SW4B
VINREFDDR is supplied by SW5
CLK32KVCC is supplied by SW3
CLK32KVCC is supplied by SW5
Tied to VCOREDIG (Check the MC34708 Data Sheet for further reference on the
power up sequence and default values)
Tied to ground (Check the MC34708 Data Sheet for further reference on the
power up sequence and default values)
Tied to VCOREDIG (Check the MC34708 Data Sheet for further reference on the
power up sequence and default values)
Tied to ground (Check the MC34708 Data Sheet for further reference on the
power up sequence and default values)
Tied to VCOREDIG (Check the MC34708 Data Sheet for further reference on the
power up sequence and default values)
Tied to ground (Check the MC34708 Data Sheet for further reference on the
power up sequence and default values)
Board, Rev. 2.0
Function
Setup Configuration
18