IDT7130LA25PF IDT, Integrated Device Technology Inc, IDT7130LA25PF Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT7130LA25PF
Manufacturer Part Number
IDT7130LA25PF
Description
IC SRAM 8KBIT 25NS 64TQFP
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.IDT7140LA25JGI.pdf
(19 pages)
Specifications of IDT7130LA25PF
Format - Memory
RAM
Memory Type
SRAM - Dual Port, Asynchronous
Memory Size
8K (1K x 8)
Speed
25ns
Interface
Parallel
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Package / Case
64-TQFP, 64-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
7130LA25PF
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT7130LA25PF
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
IDT7130LA25PF8
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Part Number:
IDT7130LA25PFGI
Manufacturer:
IDT
Quantity:
20 000
ADDRESS
Timing Waveform of Write Cycle No. 1, (R/W Controlled Timing)
Timing Waveform of Write Cycle No. 2, (CE Controlled Timing)
NOTES:
1. R/W or CE must be HIGH during all address transitions.
2. A write occurs during the overlap (t
3. t
4. During this period, the l/O pins are in the output state and input signals must not be applied.
5. If the CE LOW transition occurs simultaneously with or after the R/W LOW transition, the outputs remain in the HIGH impedance state.
6. Timing depends on which enable signal (CE or R/W) is asserted last.
7. This parameter is determined be device characterization, but is not production tested. Transition is measured 0mV from steady state with the Output Test Load
8. If OE is LOW during a R/W controlled write cycle, the write pulse width must be the larger of t
DATA
ADDRESS
DATA
IDT7130SA/LA and IDT7140SA/LA
High-Speed 1K x 8 Dual-Port Static SRAM
DATA
(Figure 2).
bus for the required t
WR
R/W
is measured from the earlier of CE or R/W going HIGH to the end of the write cycle.
OUT
R/W
OE
CE
CE
IN
IN
DW
. If OE is HIGH during a R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the specified t
t
EW
AS
t
AS
or t
(6)
(6)
WP
(4)
) of CE = V
IL
and R/W = V
t
WZ
(7)
t
AW
t
IL.
AW
t
WC
t
t
WC
WP
t
EW
11
(2)
(2)
Military, Industrial and Commercial Temperature Ranges
t
DW
WP
or (t
t
DW
WZ
+ t
DW
) to allow the I/O drivers to turn off data to be placed on the
t
WR
(3)
t
WR
t
(3)
t
DH
OW
t
DH
t
HZ
(1,5)
(1,5,8)
(7)
t
HZ
(4)
(7)
2689 drw 11
2689 drw 10
WP
.