NAND512W3A0AN6 STMicroelectronics, NAND512W3A0AN6 Datasheet - Page 29
![IC FLASH 512MBIT 48TSOP](/photos/7/26/72669/497-48-tsop_series_sml.jpg)
NAND512W3A0AN6
Manufacturer Part Number
NAND512W3A0AN6
Description
IC FLASH 512MBIT 48TSOP
Manufacturer
STMicroelectronics
Datasheet
1.NAND128W3A2BN6E.pdf
(56 pages)
Specifications of NAND512W3A0AN6
Format - Memory
FLASH
Memory Type
FLASH - Nand
Memory Size
512M (64M x 8)
Interface
Parallel
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Speed
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NAND512W3A0AN6
Manufacturer:
ST
Quantity:
106
Part Number:
NAND512W3A0AN6
Manufacturer:
ST
Quantity:
20 000
Figure 21. Automatic Page 0 Read at Power-Up (Chip Enable Don’t Care Disabled)
SOFTWARE ALGORITHMS
This section gives information on the software al-
gorithms that ST recommends to implement to
manage the Bad Blocks and extend the lifetime of
the NAND device.
NAND Flash memories are programmed and
erased by Fowler-Nordheim tunneling using a high
voltage. Exposing the device to a high voltage for
extended periods can cause the oxide layer to be
damaged. For this reason, the number of program
and erase cycles is limited (see
ue) and it is recommended to implement Garbage
Collection, a Wear-Leveling Algorithm and an Er-
ror Correction Code, to extend the number of pro-
gram and erase cycles and increase the data
retention.
To help integrate a NAND memory into an applica-
tion ST Microelectronics can provide:
Contact the nearest ST Microelectronics sales of-
fice for more details.
Bad Block Management
Devices with Bad Blocks have the same quality
level and the same AC and DC characteristics as
devices where all the blocks are valid. A Bad Block
does not affect the performance of valid blocks be-
cause it is isolated from the bit line and common
source line by a select transistor.
The devices are supplied with all the locations in-
side valid blocks erased (FFh). The Bad Block In-
formation is written prior to shipping. Any block
where the 6th Byte/ 1st Word in the spare area of
I/O
RB
A Demo board with NAND simulation software
for PCs
File System OS Native reference software,
which supports the basic commands of file
management.
(Read Busy time)
tBLBH1
Busy
Table 14.
Data Out
Page 0
tBLBH1
NAND128-A, NAND256-A, NAND512-A, NAND01G-A
for val-
Busy
Data Out
Page 1
the 1st or 2nd page (if the 1st page is Bad) does
not contain FFh is a Bad Block.
The Bad Block Information must be read before
any erase is attempted as the Bad Block Informa-
tion may be erased. For the system to be able to
recognize the Bad Blocks based on the original in-
formation it is recommended to create a Bad Block
table following the flowchart shown in
Block Replacement
Over the lifetime of the device additional Bad
Blocks may develop. In this case the block has to
be replaced by copying the data to a valid block.
These additional Bad Blocks can be identified as
attempts to program or erase them will give errors
in the Status Register.
As the failure of a page program operation does
not affect the data in other pages in the same
block, the block can be replaced by re-program-
ming the current data and copying the rest of the
replaced block to an available valid block. The
Copy Back Program command can be used to
copy the data to a valid block.
See the
tails.
Refer to
dure to follow if an error occurs during an opera-
tion.
Table 13. Block Failure
tBLBH1
Operation
Program
Erase
Read
Busy
“Copy Back
Table 13.
Data Out
Page 2
tBLBH1
Program” section for more de-
for the recommended proce-
Recommended Procedure
Block Replacement or ECC
Block Replacement
Busy
ECC
Page Nth
Data Out
Figure 22.
ai08444
29/56