XCF02SVO20C Xilinx Inc, XCF02SVO20C Datasheet - Page 32

• Manufacturer Part Number: XCF02SVO20C
• Description: IC PROM IN SYST PRG 3.3V 20TSSOP
• Manufacturer: Xilinx Inc

Specifications of XCF02SVO20C

• Programmable Type: In System Programmable
• Memory Size: 2Mb
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-TSSOP (0.173", 4.40mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Revision History
The following table shows the revision history for this document.
DS123 (v2.18) May 19, 2010
Product Specification
04/29/03
06/03/03
11/05/03
11/18/03
12/15/03
05/07/04
Date
R
Version
1.0
1.1
2.0
2.1
2.2
2.3
Xilinx Initial Release.
Made edits to all pages.
Major revision.
Pinout corrections as follows:
•
•
•
• Added specification (4.7kΩ) for recommended pull-up resistor on OE/RESET pin to section
• Added paragraph to section
• Section
• Section
•
• Section
• Section
•
• Section
•
• Section
• Section
• Section
• (Continued on next page)
• Section
• Section
• Section
•
Table
• For VO48 package, removed 38 from VCCINT and added it to VCCO.
• For FS48 package, removed pin D6 from VCCINT and added it to VCCO.
Table 14
• For pin D6, changed name from VCCINT to VCCO.
• For pin A4, changed name from GND to DNC.
Figure 8
"Reset and Power-On Reset Activation," page
and/or buffer on the DONE pin.
itemized features.
descriptive text.
Table 2, page
to tie CF High if it is not tied to the FPGA’s PROG_B (PROGRAM) input.
Figure 6, page
CF pin in each configuration.
Table 12, page
the Low state of CF.
• Revised footnote callout number on T
• Added Footnote (2) callout to T
• Added Typical (Typ) parameter columns and parameters for V
• Added 1.5V operation parameter row to V
• Revised V
• Added parameter row T
• Added parameter row and parameters for parallel configuration mode, ’P’ devices, to I
• Added Footnote (1) and Footnote (2) with callouts in the Test Conditions column for I
• Corrected description for second T
• Revised Footnote (7) to indicate V
• Applied Footnote (7) to second T
Footnote (5)T
Table 14, page
• Added additional state conditions to CLK description.
• Added function of resetting the internal address counter to CF description.
I
CCINTS
13:
"Initiating FPGA Configuration," page 10
"Features," page
"Description," page 1
"Design Revisioning," page
"I/O Input Voltage Tolerance and Power Sequencing," page
"Absolute Maximum Ratings," page
"Supply Voltage Requirements for Power-On Reset and Power-Down," page
"Recommended Operating Conditions," page
"DC Characteristics Over Operating Conditions," page
"AC Characteristics Over Operating Conditions," page
"AC Characteristics Over Operating Conditions When Cascading," page
(VO48 package): For pin 38, changed name from VCCINT to VCCO.
(FS48 package):
, I
CCOS
IH
CYC
3: Updated Virtex®-II configuration bitstream sizes.
16, through
25: Added CF column to truth table, and added an additional row to document
39:
Min, 2.5V operation, from 2.0V to 1.7V.
, and I
Min and T
www.xilinx.com
Platform Flash In-System Programmable Configuration PROMs
CCJS
1: Added package styles and 33 MHz configuration speed limit to
IN
Figure 13, page
CAC
"Standby Mode," page
, to define active and standby mode requirements.
and Max parameters
and following: Added state conditions for CF and BUSY to the
Min formulas.
VCC
CYC
8: Rewritten.
CCO
CAC
.
OER
parameter line.
Revision
= 3.3V.
parameter line to show parameters for 1.8V V
23: Added footnote indicating the directionality of the
13: Revised V
IL
from Footnote (4) to Footnote (3).
11.
and V
and following, five instances: Added instruction
12, concerning use of a pull-up resistor
IH
14:
, ’P’ devices.
IN
and V
16:
15:
CCINT
TS
11: Rewritten.
for ’P’ devices.
and V
CCO
/V
23: Revised
CCJ
13:
.
CCJ
CCO
CCO
,
.
.
32