ADE7752ARZ Analog Devices Inc, ADE7752ARZ Datasheet - Page 20

• Manufacturer Part Number: ADE7752ARZ
• Description: IC ENERGY METERING DETEC 24-SOIC
• Manufacturer: Analog Devices Inc

Specifications of ADE7752ARZ

• Input Impedance: 450 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 2.4V
• Voltage - I/o Low: 0.8V
• Current - Supply: 6mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (0.300", 7.50mm Width)
• Meter Type: 3 Phase
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADE7752/ADE7752A
TRANSFER FUNCTION
FREQUENCY OUTPUTS F1 AND F2
The ADE7752 calculates the product of six voltage signals (on
current channel and voltage channel) and then low-pass filters
this product to extract real power information. This real power
information is then converted to a frequency. The frequency
information is output on F1 and F2 in the form of active high
pulses. The pulse rate at these outputs is relatively low, such as
29.32 Hz maximum for ac signals with SCF = 1; S0 = S1 = 1 (see
Table 6). This means that the frequency at these outputs is
generated from real power information accumulated over a
relatively long period of time. The result is an output frequency
that is proportional to the average real power. The averaging of
the real power signal is implicit to the digital-to-frequency
conversion. The output frequency or pulse rate is related to the
input voltage signals by the following equation:
where:
Freq = the output frequency on F1 and F2 (Hz).
V
channels (V).
I
channels (V).
V
F
logic inputs SCF, S0, and S1 (see Table 5).
Table 5. F
SCF
0
1
0
1
0
1
0
1
1
Example 1
Thus, if full-scale differential dc voltages of +500 mV are
applied to VA, VB, VC, IA, IB, and IC, respectively (500 mV is
the maximum differential voltage that can be connected to
current and voltage channels), the expected output frequency is
calculated as follows:
A,
F
CLKIN frequency is altered.
1–7
AN,
REF
1–7
I
B,
= one of seven possible frequencies selected by using the
is a fraction of the master clock and therefore varies if the specified
= the reference voltage (2.4 V ± 8%) (V).
V
Freq
and I
BN,
and V
=
1–7
C
= the differential rms voltage signal on current
. 6
Frequency Selection
181
CN
S1
0
0
0
0
1
1
1
1
= the differential rms voltage signal on voltage
×
(
V
AN
×
I
S0
0
0
1
1
0
0
1
1
A
+
V
BN
V
1
REF
×
I
2
B
F
1.27
1.19
5.09
4.77
19.07
19.07
76.29
0.60
+
1–7
V
CN
(Hz)
×
I
C
)
×
F
1
−
Rev. C | Page 20 of 24
7
Note that if the on-chip reference is used, actual output fre-
quencies may vary from device to device due to reference
tolerance of ±8%.
Example 2
In this example, with ac voltages of ±500 mV peak applied to
the voltage channels and current channels, the expected output
frequency is calculated as follows:
Note that if the on-chip reference is used, actual output fre-
quencies may vary from device to device due to reference
tolerance of ±8%.
As can be seen from these two example calculations, the
maximum output frequency for ac inputs is always half of that
for dc input signals. The maximum frequency also depends on
the number of phases connected to the ADE7752. In a 3-phase
3-wire delta service, the maximum output frequency is different
from the maximum output frequency in a 3-phase
4-wire Wye service. The reason is that there are only two phases
connected to the analog inputs, but also that in a delta service,
the current channel input and voltage channel input of the same
phase are not in phase in normal operation.
Example 3
In this example, the ADE7752 is connected to a 3-phase 3-wire
delta service as shown in Figure 21. The total real energy
calculation processed in the ADE7752 can be expressed as
where V
C, respectively. I
B, respectively.
F
V
0.5 V(rms of dc = dc)
V
Total Real Power = (V
V
V
Freq
F
Freq
1–7
AN
REF
1
AN
REF
−
7
A
= 0.60 Hz, SCF = S0 = S1 = 1
= V = V
= 2.4 V (nominal reference value)
=
, V
=
=
=
=
=
. 0
V
500
2
3
3
B
BN
60
, and V
B
BN
4 .
×
×
. 6
V
. 6
Hz
mV
=
A
181
181
(
and I
V
nominal
CN
,
CN
SCF
2
C
peak
×
= IA = IB = IC = 500 mV dc =
×
represent the voltage on Phase A, B, and
×
=
0
B
0
B
5 .
5 .
represent the current on Phase A and
IA
2
=
2
AC
4 .
×
A
×
S
reference
×
=
2
0
0
− V
0
2
5 .
5 .
IB
=
=
4 .
×
C
×
S
0
2
=
) × I
1
0
5 .
. 0
2
6 .
=
IC
60
1
value
=
Vrms
A
+ (V
=
. 0
. 0
24
)
483
B
Hz
B
− V
Hz
C
) × I
B
B