PCA9511ADP,118 NXP Semiconductors, PCA9511ADP,118 Datasheet - Page 6

• Manufacturer Part Number: PCA9511ADP,118
• Description: IC HOTSWAP I2C/SMBUS BUFF 8TSSOP
• Manufacturer: NXP Semiconductors
• Type: I²C-Bus and SMBus Switchr

Specifications of PCA9511ADP,118

• Package / Case: 8-TSSOP
• Applications: Hot-Swap/SMB Buffer
• Internal Switch(s): Yes
• Current Limit: 50mA
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Logic Family: PCA
• Maximum Operating Temperature: 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Number Of Lines (input / Output): 3 / 3
• Propagation Delay Time: 70 ns
• Logic Type: Bus Buffer
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-3360-2; 935279308118; PCA9511ADP-T

NXP Semiconductors
PCA9511A_4
Product data sheet
8.4 Propagation delays
on the accelerator turns the pull-down off. If the V
detected, the pull-down will turn off and will not turn back on until a falling edge is
detected.
Consider a system with three buffers connected to a common node and communication
between the Master and Slave B that are connected at either end of buffer A and buffer B
in series as shown in
V
Slave B and then from Slave B to Master. Before the direction change you would observe
V
of buffer B and buffer C would be ~0.5 V, but Slave B is driving 0.4 V, so the voltage at
Slave B is 0.4 V. The output of buffer C is ~0.5 V. When the Master pull-down turns off, the
input of buffer A rises and so does its output, the common node, because it is the only part
driving the node. The common node will rise to 0.5 V before buffer B’s output turns on, if
the pull-up is strong the node may bounce. If the bounce goes above the threshold for the
rising edge accelerator ~0.6 V the accelerators on both buffer A and buffer C will fire
contending with the output of buffer B. The node on the input of buffer A will go HIGH as
will the input node of buffer C. After the common node voltage is stable for a while the
rising edge accelerators will turn off and the common node will return to ~0.5 V because
the buffer B is still on. The voltage at both the Master and Slave C nodes would then fall to
~0.6 V until Slave B turned off. This would not cause a failure on the data line as long as
the return to 0.5 V on the common node (~0.6 V at the Master and Slave C) occurred
before the data setup time. If this were the SCL line, the parts on buffer A and buffer C
would see a false clock rather than a stretched clock, which would cause a system error.
The delay for a rising edge is determined by the combined pull-up current from the bus
resistors and the rise time accelerator current source and the effective capacitance on the
lines. If the pull-up currents are the same, any difference in rise time is directly
proportional to the difference in capacitance between the two sides. The t
negative if the output capacitance is less than the input capacitance and would be positive
if the output capacitance is larger than the input capacitance, when the currents are the
same.
The t
below 0.7V
maximum slew rate, and even if the input slew rate is slow enough that the output catches
up it will still lag the falling voltage of the input by the offset voltage. The maximum t
occurs when the input is driven LOW with zero delay and the output is still limited by its
Fig 4.
OL
IL
at the input of buffer A of 0.3 V and its output, the common node, is ~0.4 V. The output
of Slave B (when acknowledging) is 0.4 V with the direction changing from Master to
PHL
can never be negative because the output does not start to fall until the input is
System with 3 buffers connected to common node
CC
, and the output turn on has a non-zero delay, and the output has a limited
Figure
Rev. 04 — 19 August 2009
MASTER
4. Consider if the V
buffer A
common
Hot swappable I
node
OL
buffer C
buffer B
IL
at the input of buffer A is 0.3 V and the
is above ~0.6 V and a rising edge is
2
SLAVE C
SLAVE B
C-bus and SMBus bus buffer
002aab581
PCA9511A
© NXP B.V. 2009. All rights reserved.
PLH
may be
PHL
6 of 24