BD6519FJ-E2 Rohm Semiconductor, BD6519FJ-E2 Datasheet - Page 13

• Manufacturer Part Number: BD6519FJ-E2
• Description: IC SWITCH HIGH SIDE 1CH SOP-J8
• Manufacturer: Rohm Semiconductor
• Type: High Sider

Specifications of BD6519FJ-E2

• Input Type: Non-Inverting
• Number Of Outputs: 1
• On-state Resistance: 100 mOhm
• Current - Output / Channel: 500mA
• Current - Peak Output: 1A
• Voltage - Supply: 3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOPJ
• Primary Input Voltage: 5V
• No. Of Outputs: 1
• Output Voltage: 5V
• Output Current: 500mA
• Voltage Regulator Case Style: SOP
• No. Of Pins: 8
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC
• Output Power: 560 mW
• Input Voltage: 3 V to 5.5 V
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: BD6519FJ-E2TR

Functional description (BD2041AFJ/2051AFJ)
© 2009 ROHM Co., Ltd. All rights reserved.
BD2041AFJ,BD2051AFJ,BD6518FJ,BD6519FJ
www.rohm.com
1. Switch operation
2. Thermal shutdown circuit (TSD)
3. Over current detection (OCD)
4. Under voltage lockout (UVLO)
5. Error flag (/OC) output
IN terminal and OUT terminal are connected to the drain and the source of switch MOSFET respectively. And the IN
terminal is used also as power source input to internal control circuit.
When the switch is turned on from EN/EN control input, IN terminal and OUT terminal are connected by a 80mΩ switch. In
on status, the switch is bidirectional. Therefore, when the potential of OUT terminal is higher than that of IN terminal,
current flows from OUT terminal to IN terminal.
Since a parasitic diode between the drain and the source of switch MOSFET is canceled, in the off status, it is possible to
prevent current from flowing reversely from OUT to IN.
If over current would continue, the temperature of the IC would increase drastically. If the junction temperature were
beyond 140°C (typ.) in the condition of over current detection, thermal shutdown circuit operates and makes power switch
turn off and outputs error flag (/OC). Then, when the junction temperature decreases lower than 120°C (typ.), power switch
is turned on and error flag (/OC) is cancelled. Unless the fact of the increasing chips temperature is removed or the output
of power switch is turned off, this operation repeats.
The thermal shutdown circuit operates when the switch is on (EN,/EN signal is active).
The over current detection circuit limits current (I
MOSFET exceeds a specified value. There are three types of response against over current. The over current detection
circuit works when the switch is on (EN,/EN signal is active).
3-1. When the switch is turned on while the output is in shortcircuit status
3-2. When the output shortcircuits while the switch is on
3-3. When the output current increases gradually
UVLO circuit prevents the switch from turning on until the V
the switch turns on, then UVLO shuts off the power switch. UVLO has hysteresis of a 100mV(Typ).
Under voltage lockout circuit works when the switch is on (EN,/EN signal is active).
Error flag output is N-MOS open drain output. At detection of over current, thermal shutdown, low level is output.
Over current detection has delay filter. This delay filter prevents instantaneous current detection such as inrush current at
switch on, hot plug from being informed to outside.
When the switch is turned on while the output is in shortcircuit status or so, the switch gets in current limit status soon.
When the output shortcircuits or large capacity is connected while the switch is on, very large current flows until the
over current limit circuit reacts. When the current detection, limit circuit works, current limitation is carried out.
When the output current increases gradually, current limitation does not work until the output current exceeds the over
current detection value. When it exceeds the detection value, current limitation is carried out.
SC
) and outputs error flag (/OC) when current flowing in each switch
13/18
IN
exceeds 2.3V(Typ.). If the V
IN
drops below 2.2V(Typ.) while
Technical Note
2009.05 - Rev.A