E-L9826TR STMicroelectronics, E-L9826TR Datasheet - Page 12
![IC DRIVER OCTAL LOW SIDE SOIC-20](/photos/6/56/65691/497-20-soic__7_5mm_width__series_sml.jpg)
E-L9826TR
Manufacturer Part Number
E-L9826TR
Description
IC DRIVER OCTAL LOW SIDE SOIC-20
Manufacturer
STMicroelectronics
Type
Low Sider
Specifications of E-L9826TR
Input Type
SPI
Number Of Outputs
8
On-state Resistance
1.5 Ohm
Current - Peak Output
1.1A
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 150°C
Mounting Type
Surface Mount
Package / Case
20-SOIC (7.5mm Width)
Supply Voltage (min)
4.5 V
Supply Current
5 mA
Maximum Operating Temperature
+ 150 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 65 C
Number Of Drivers
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Output / Channel
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
E-L9826TR
Manufacturer:
ST
Quantity:
9 492
Part Number:
E-L9826TR
Manufacturer:
ST
Quantity:
20 000
4 Functional Description
4.4
12/17
Diagnostics
The output voltage at all outputs is compared with the diagnostic threshold, typ 0,38 · V
Outputs 1 and 2 features dedicated fault latches. The output status signal is filtered and
latched. The fault latches are cleared during NCS low. The latch stores the status bit, so the
first reading after the error occurred might be wrong. The second reading is right.
Table 6.
Fault condition 1) "output short circuit to Vbat" : the output was switched on and the voltage at
the output exceeds the diagnostics threshold. The output operates in current regulation mode
or has been switched off due to thermal shutdown. The status bit is low.
Fault condition 2) "open load" or "output short circuit to GND" : the output is switched off and
the voltage at the output drops below the diagnostics threshold, because the load current is
lower than the output diagnostic current source, the load is interrupted. The diagnostic bit is
low.
For outputs 3 to 8 the output status signals, are fed directly to the SPI register.
Table 7.
The fault condition 1) "output short circuit to Vbat" : the output was switched on and the voltage
at the output exceeded the diagnostics threshold due to overcurrent, the output overload latch
was set and the output has been switched off. The diagnostic bit is high.
Fault condition 2) "open load" or "output short circuit to GND" is the same as of outputs 1 and
2. At the falling edge of NCS the output status data are transferred to the shift register.
When NSC is low, data bits contained in the shift register are transferred to SDO output et
every rising CLK edge.
Output 1 ... 8
Output 1, 2
off
off
on
on
off
off
on
on
Diagnostic Table for outputs 1 and 2 in parallel controlled mode:
Diagnostic Table for outputs 1 to 8 in SPI controlled mode
> DG-threshold
< DG-threshold
< DG-threshold
> DG-threshold
> DG-threshold
< DG-threshold
< DG-threshold
> DG-threshold
Output-voltage
Output-voltage
CD00002120
Status-bit
Status-bit
high
high
low
low
high
high
low
low
correct operation
fault condition 2)
correct operation
fault condition 1)
correct operation
fault condition 2)
correct operation
fault condition 1)
:
Output-mode
Output-mode
CC
L9826
.