VND830SPTR-E STMicroelectronics, VND830SPTR-E Datasheet
VND830SPTR-E
Specifications of VND830SPTR-E
Available stocks
Related parts for VND830SPTR-E
VND830SPTR-E Summary of contents
Page 1
... Output CC shorted to V transient automatically turns off in case of ground pin disconnection. Tube VND830SP-E VND830SP PowerSO-10™ is detected in the off state. Device CC Tape and Reel VND830SPTR-E Rev. 1 1/20 ...
Page 2
VND830SP-E Figure 2. Block Diagram V CC CLAMP GND INPUT1 STATUS1 LOGIC OVERTEMP. 1 INPUT2 STATUS2 OVERTEMP. 2 Table 3. Absolute Maximum Ratings Symbol DC Supply Voltage Reverse DC Supply Voltage Reverse ...
Page 3
Figure 3. Configuration Diagram (Top View) & Suggested Connections for Unused and N.C. Pins GROUND INPUT 1 STATUS 1 STATUS 2 INPUT 2 Connection / Pin Status Floating To Ground Figure 4. Current and Voltage Conventions V IN1 V STAT1 ...
Page 4
VND830SP-E ELECTRICAL CHARACTERISTICS (8V<V <36V; -40°C < T < 150°C, unless otherwise specified (Per each channel) Table 5. Power Output Symbol Parameter V (**) Operating Supply Voltage CC V (**) Undervoltage Shut-down USD V (**) Overvoltage Shut-down OV ...
Page 5
ELECTRICAL CHARACTERISTICS (continued) Table 8. Status Pin Symbol Parameter V Status Low Output Voltage I STAT I Status Leakage Current LSTAT Status Pin Input C STAT Capacitance V Status Clamp Voltage SCL Table 9. Switching (V =13V) CC Symbol Parameter ...
Page 6
VND830SP-E Figure 5. OPEN LOAD STATUS TIMING (with external pull-up) V OUT V INn V STATn t DOL(off) Table 12. Truth Table CONDITIONS Normal Operation Current Limitation Overtemperature Undervoltage Overvoltage Output Voltage > Output Current < ...
Page 7
Figure 6. Switching Time Waveforms V OUTn 80% dV /dt OUT (on) V INn t d(on) Table 13. Electrical Transient Requirements On V ISO T/R 7637/1 Test Pulse +25 ...
Page 8
VND830SP-E Figure 7. Waveforms INPUT n OUTPUT VOLTAGE STATUS INPUT n OUTPUT VOLTAGE STATUS INPUT n OUTPUT VOLTAGE STATUS n INPUT n OUTPUT VOLTAGE STATUS n INPUT n OUTPUT VOLTAGE STATUS ...
Page 9
Figure 8. Application Schematic +5V +5V +5V R prot R C prot R prot R prot GND PROTECTION NETWORK REVERSE BATTERY Solution 1: Resistor in the ground line (R can be used with any type of load. The following is ...
Page 10
VND830SP-E C I/Os PROTECTION ground protection network is used and negative transient are present on the V line, the control pins will CC be pulled negative. ST suggests to insert a resistor (R in line to prevent the ...
Page 11
Figure 10. Off State Output Current IL(off1) (uA) 2.5 2.25 Off state 2 Vcc=36V Vin=Vout=0V 1.75 1.5 1.25 1 0.75 0.5 0.25 0 -50 - (°C) Figure 11. Input Clamp Voltage Vicl (V) 8 7.8 ...
Page 12
VND830SP-E Figure 16. On State Resistance Vs T Ron (mOhm) 160 140 Iout=2A Vcc=8V; 13V & 36V 120 100 -50 - (°C) Figure 17. Openload On State Detection Threshold Iol ...
Page 13
Figure 22. Input Hysteresis Voltage Vhyst (V) 1.5 1.4 1.3 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 -50 - (°C) Figure 23. Turn-on Voltage Slope dVout/dt(on) (V/ms) 800 700 Vcc=13V Rl=6.5Ohm 600 500 400 ...
Page 14
VND830SP-E Figure 27. Maximum turn off current versus load inductance I LMAX (A) 100 Single Pulse at T =150ºC Jstart B= Repetitive pulse at T =100ºC Jstart C= Repetitive Pulse at T =125ºC Jstart Conditions: ...
Page 15
PowerSO-10™ Thermal Data Figure 28. PowerSO-10™ PC Board Layout condition of R and thickness=35 m, Copper areas: from minimum pad lay-out to 8cm Figure 29 PCB copper area in open box free air condition thj-amb ...
Page 16
VND830SP-E Figure 30. PowerSO-10 Thermal Impedance Junction Ambient Single Pulse ZTH (°C/W) 1000 100 10 1 0.1 0.01 0.0001 0.001 Figure 31. Thermal fitting model of a double channel HSD in PowerSO-10 Tj_1 Pd1 ...
Page 17
PACKAGE MECHANICAL Table 15. PowerSO-10™ Mechanical Data Symbol A A (*) (*) C C (*) (*) E4 E4 (*) (*) H H (*) (*) a (*) ...
Page 18
VND830SP-E Figure 33. Suggested Pad Layout And Tube Shipment (No Suffix) PowerSO-10™ 14.6 - 14.9 10 6.30 0. 0. Figure 34. Tape ...
Page 19
REVISION HISTORY Date Revision Oct. 2004 1 - First Issue. Description of Changes VND830SP-E 19/20 ...
Page 20
... No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics ...