VND830SPTR-E STMicroelectronics, VND830SPTR-E Datasheet - Page 10

• Manufacturer Part Number: VND830SPTR-E
• Description: IC DRIVER HIGH SIDE 2CH PWRSO10
• Manufacturer: STMicroelectronics
• Type: High Sider

Specifications of VND830SPTR-E

• Input Type: Non-Inverting
• Number Of Outputs: 2
• On-state Resistance: 60 mOhm
• Current - Peak Output: 9A
• Voltage - Supply: 5.5 V ~ 36 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: PowerSO-10 Exposed Bottom Pad
• Switch Type: High Side
• Power Switch Family: VND830SP
• Power Switch On Resistance: 60mOhm
• Output Current: 9A
• Mounting: Surface Mount
• Supply Current: 12uA
• Package Type: PowerSO
• Operating Temperature (min): -40C
• Operating Temperature (max): 150C
• Operating Temperature Classification: Automotive
• Pin Count: 10
• Power Dissipation: 73500W
• Supply Voltage (min): 5.5 V
• Maximum Power Dissipation: 73500 mW
• Maximum Operating Temperature: + 150 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output / Channel: -
• Lead Free Status / Rohs Status: Compliant

VND830SP-E
If a ground protection network is used and negative
transient are present on the V
be pulled negative. ST suggests to insert a resistor (R
in line to prevent the C I/Os pins to latch-up.
The value of these resistors is a compromise between
the leakage current of C and the current required by the
HSD I/Os (Input levels compatibility) with the latch-up
limit of C I/Os.
Calculation example:
For V
5k
Recommended R
OPEN LOAD DETECTION IN OFF STATE
Off state open load detection requires an external pull-up
resistor (R
positive supply voltage (V
Figure 9. Open Load detection in off state
10/20
C I/Os PROTECTION:
-V
CCpeak
CCpeak
R
prot
/I
PU
latchup
= - 100V and I
) connected between OUTPUT pin and a
65k .
prot
R
STATUS
value is 10k
prot
INPUT
latchup
PU
(V
) like the +5V line used to
OH C
CC
line, the control pins will
-V
20mA; V
IH
-V
GND
DRIVER
LOGIC
OH C
+
) / I
IHmax
4.5V
GROUND
prot
+
-
)
V
V
CC
OL
V batt.
R
supply the microprocessor.
The external resistor has to be selected according to the
following requirements:
1) no false open load indication when load is connected:
2) no misdetection when load is disconnected: in this
Because I
pulled high (up to several mA), the pull-up resistor R
should be connected to a supply that is switched OFF
when the module is in standby.
The values of V
the Electrical Characteristics section
case the V
results in the following condition R
I
in this case we have to avoid V
V
V
L(off2)
Olmin
OUT
=(V
.
OUT
; this results in the following condition
s(OFF)
PU
/(R
OUT
I
OLmin
L(off2)
L
may significantly increase if V
+R
has to be higher than V
, V
PU
))R
OLmax
V
L
<V
PU
and I
Olmin.
R
R
OUT
PU
L
L(off2)
PU
to be higher than
<(V
are available in
PU–
OLmax
V
OLmax
out
; this
PU
is
)/