L6599ADTR STMicroelectronics, L6599ADTR Datasheet - Page 30
![IC RESONANT CONVRTR CTRLR 16SOIC](/photos/7/48/74892/l6599adtr_sml.jpg)
L6599ADTR
Manufacturer Part Number
L6599ADTR
Description
IC RESONANT CONVRTR CTRLR 16SOIC
Manufacturer
STMicroelectronics
Specifications of L6599ADTR
Applications
Resonant Converter Controller
Voltage - Supply
8.85 V ~ 16 V
Current - Supply
3.5mA
Operating Temperature
0°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
16-SOIC (3.9mm Width)
Operating Temperature Classification
Automotive
Mounting
Surface Mount
Pin Count
16
Operating Supply Voltage
8.15 V, 10.7 V, 17 V
Maximum Operating Temperature
+ 150 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
For Use With
497-10542 - BOARD EVAL BASED ON L6599497-8429 - BOARD ADAPTER L6599/STP12NM50N497-5496 - EVAL BOARD FOR L6599
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Input
-
Lead Free Status / Rohs Status
Compliant
Other names
497-8519-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
L6599ADTR
Manufacturer:
U-BLOX
Quantity:
21 000
Part Number:
L6599ADTR
Manufacturer:
ST
Quantity:
20 000
Part Number:
L6599ADTR-2LF
Manufacturer:
ST
Quantity:
20 000
Application information
7.7
30/36
the function is not used the pin has to be connected to a voltage greater than 1.24 V but
lower than 6V (worst-case value of the 7 V threshold).
Bootstrap section
The supply of the floating high-side section is obtained by means of a bootstrap circuitry.
This solution normally requires a high voltage fast recovery diode (D
charge the bootstrap capacitor C
replaces this external diode. It is realized by means of a high voltage DMOS, working in the
third quadrant and driven synchronously with the low side driver (LVG), with a diode in
series to the source, as shown in
Figure 31. Bootstrap supply: a) standard circuit;
The diode prevents any current can flow from the VBOOT pin back to Vcc in case that the
supply is quickly turned off when the internal capacitor of the pump is not fully discharged.
To drive the synchronous DMOS it is necessary a voltage higher than the supply voltage
Vcc. This voltage is obtained by means of an internal charge pump (
The bootstrap structure introduces a voltage drop while recharging CBOOT (i.e. when the
low side driver is on), which increases with the operating frequency and with the size of the
external power MOS. It is the sum of the drop across the R
across the series diode. At low frequency this drop is very small and can be neglected but,
as the operating frequency increases, it must be taken into account. In fact, the drop
reduces the amplitude of the driving signal and can significantly increase the R
external high-side MOSFET and then its conductive loss.
This concern applies to converters designed with a high resonance frequency (indicatively,
> 150 kHz), so that they run at high frequency also at full load. Otherwise, the converter will
run at high frequency at light load, where the current flowing in the MOSFETs of the half-
bridge leg is low, so that, generally, an R
check this point anyway and the following equation is useful to compute the drop on the
bootstrap driver:
b) internal bootstrap synchronous diode
Doc ID 15308 Rev 5
BOOT
Figure 31
. In the L6599A a patented integrated structure,
(DS)ON
b.
rise is not an issue. However, it is wise to
(DS)ON
and the forward drop
BOOT
Figure 31
,
Figure 31
b).
(DS)ON
L6599A
a) to
of the