SA56004CD,112 NXP Semiconductors, SA56004CD,112 Datasheet - Page 20
![IC TEMP SENSOR 8-SOIC](/photos/5/44/54425/568-8-soic_sot96-1_sml.jpg)
SA56004CD,112
Manufacturer Part Number
SA56004CD,112
Description
IC TEMP SENSOR 8-SOIC
Manufacturer
NXP Semiconductors
Datasheet
1.SA56004BDP118.pdf
(36 pages)
Specifications of SA56004CD,112
Package / Case
8-SOIC (3.9mm Width)
Function
Temp Monitoring System (Sensor)
Topology
ADC (Sigma Delta), Multiplexer, Register Bank
Sensor Type
External & Internal
Sensing Temperature
-40°C ~ 125°C, External Sensor
Output Type
I²C™/SMBus™
Output Alarm
Yes
Output Fan
Yes
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Temperature Threshold
+ 165 C
Full Temp Accuracy
1 %
Digital Output - Bus Interface
SMBus
Digital Output - Number Of Bits
11 bit
Supply Voltage (max)
3.6 V
Supply Voltage (min)
3 V
Description/function
Digital Temperature Sensor
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Supply Current
500 uA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
568-3615 - DEMO BOARD I2C
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
568-3333-5
935274539112
SA56004CD
935274539112
SA56004CD
NXP Semiconductors
8. Simplified system diagram
SA56004X_5
Product data sheet
Fig 10. Simplified system diagram
(1) Typical value; placed close to temperature sensor.
remote sensor
2N3904 (NPN), 2N3906 (PNP),
or similar standalone, ASIC or
microprocessor thermal diode
7.10.1 Serial interface reset
+5 V
shielded twisted pair
If the SMBus master attempts to reset the SA56004X while the SA56004X is controlling
the data line and transmitting on the data line, the SA56004X must be returned to a known
state in the communication protocol. This may be accomplished in two ways:
1. When the SDATA is LOW, the SA56004X SMBus state machine resets to the SMBus
2. When the SDATA is HIGH, the master initiates an SMBus START. The SA56004X will
idle state if SCLK is held LOW for more than 35 ms (maximum TIMEOUT period).
According to SMBus specification 2.0 , all devices are required to time-out when the
SCLK line is held LOW for 25 ms to 35 ms. Therefore, to insure a time-out of all
devices on the bus, the SCLK line must be held LOW for at least 35 ms.
respond properly to a SMBus START condition only during the data retrieving cycle.
After the START, the SA56004X will expect an SMBus Address byte.
2.2 nF (1)
FAN CONTROL
100 nF
V
CIRCUIT
V
DD
DD
R
10 k
Rev. 05 — 22 May 2008
1
2
3
4
V
D+
D
T_CRIT
DD
Digital temperature sensor with overtemperature alarms
SA56004X
SDATA
ALERT
SCLK
GND
8
7
6
5
10 k
R
R
10 k
R
10 k
CLOCK
DATA
INT
CONTROLLER
SA56004X
SMBus
© NXP B.V. 2008. All rights reserved.
V
DD
002aad201
20 of 36