GNM212R61A225MA01D Murata Electronics North America, GNM212R61A225MA01D Datasheet - Page 145

• Manufacturer Part Number: GNM212R61A225MA01D
• Description: CAP 2-ARRAY 2.2UF 10V X5R 0805
• Manufacturer: Murata Electronics North America
• Series: GNMr

Specifications of GNM212R61A225MA01D

• Capacitance: 2.2µF
• Voltage - Rated: 10V
• Dielectric Material: Ceramic
• Number Of Capacitors: 2
• Circuit Type: Isolated
• Temperature Coefficient: X5R
• Tolerance: ±20%
• Mounting Type: Surface Mount
• Package / Case: 0805 (2012 Metric)
• Height: 0.033" (0.85mm)
• Size / Dimension: 0.079" L x 0.049" W (2.00mm x 1.25mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: GNM212R61A225MA01

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
5. Flow Soldering
Table 2
Recommended Conditions
Pb-Sn Solder: Sn-37Pb
Lead Free Solder: Sn-3.0Ag-0.5Cu
Optimum Solder Amount for Flow Soldering
Peak Temperature
When sudden heat is given to the components, the
mechanical strength of the components should go down
because remarkable temperature change causes
deformity of components inside. And an excessively long
soldering time or high soldering temperature results in
leaching by the outer electrodes, causing poor adhesion
or a reduction in capacitance value due to loss of contact
between electrodes and end termination.
In order to prevent mechanical damage in the
components, preheating should be required for both of
the components and the PCB board. Preheating
conditions are shown in Table 2. It is required to keep
temperature differential between the soldering and the
components surface ( T) as small as possible.
When components are immersed in solvent after
mounting, be sure to maintain the temperature difference
between the component and solvent within the range
shown in Table 2.
Do not apply flow soldering to chips not listed in Table 2.
The top of the solder fillet should be lower than the
thickness of components. If the solder amount is
excessively big, the risk of cracking is higher during
board bending or under any other stressful conditions.
Continued from the preceding page.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Atmosphere
G--18/21/31
Part Number
Pb-Sn Solder
240-250 C
Air
Temperature Differential
TV150D
Lead Free Solder
250-260 C
N
2
[Standard Conditions for Flow Soldering]
[Allowable Soldering Temperature and Time]
Peak Temperature
Temperature (D)
In case of repeated soldering, the accumulated
soldering time must be within the range shown above.
270
260
250
240
230


















170 C
150 C
130 C
0
















Adhesive
T
10
60-120 seconds
Preheating
20
Continued on the following page.
Soldering
5 seconds max.
Soldering Time (sec.)
30
Up to Chip Thickness
!Caution
Gradual
Cooling
Time
143
C02E.pdf
07.2.6
23