ISL6269BCRZ Intersil, ISL6269BCRZ Datasheet

IC PWM CTRLR SYNC BUCK 16-QFN

ISL6269BCRZ

Manufacturer Part Number
ISL6269BCRZ
Description
IC PWM CTRLR SYNC BUCK 16-QFN
Manufacturer
Intersil
Datasheet

Specifications of ISL6269BCRZ

Pwm Type
Controller
Number Of Outputs
1
Frequency - Max
600kHz
Voltage - Supply
5 V ~ 25 V
Buck
Yes
Boost
No
Flyback
No
Inverting
No
Doubler
No
Divider
No
Cuk
No
Isolated
No
Operating Temperature
-10°C ~ 100°C
Package / Case
16-VQFN Exposed Pad, 16-HVQFN, 16-SQFN, 16-DHVQFN
Frequency-max
600kHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Duty Cycle
-
High-Performance Notebook PWM
Controller with Audio-Frequency Clamp
The ISL6269B IC is a Single-Phase Synchronous-Buck
PWM controller featuring Intersil's Robust Ripple Regulator
(R
response to input voltage and output load transients.
Integrated MOSFET drivers and bootstrap diode result in
fewer components and smaller implementation area.
Intersil’s R
frequency PWM and hysteretic PWM while eliminating many
of their shortcomings. R
modulator that synthesizes an AC ripple voltage signal V
analogous to the output inductor ripple current. The AC signal
V
the error amplifier output V
programmable voltage reference V
of the PWM signal. The voltage reference V
state PWM frequency. Both edges of the PWM can be
modulated in response to input voltage transients and output
load transients, much faster than conventional fixed-
frequency PWM controllers. Unlike a conventional hysteretic
converter, the ISL6269B has an error amplifier that provides
±1% voltage regulation at the FB pin.
The ISL6269B has a 1.5ms digital soft-start and can be
started into a pre-biased output voltage. A resistor divider is
used to program the output voltage setpoint. The ISL6269B
can be configured to operate in continuous-conduction-
mode (CCM) or diode-emulation-mode (DEM), which
improves light-load efficiency. In CCM the controller always
operates as a synchronous rectifier however, when DEM is
enabled the low-side MOSFET is permitted to stay off,
blocking negative current flow into the low-side MOSFET
from the output inductor.
Pinout
R
3
) technology that delivers truly superior dynamic
enters a window comparator where the lower threshold is
3
FCCM
technology combines the best features of fixed-
VCC
VIN
EN
1
2
3
4
(16 LD 4x4 QFN)
16
5
3
technology employs an innovative
TOP VIEW
ISL6269B
COMP
15
®
6
GND
1
, and the upper threshold is a
14
7
W,
13
Data Sheet
8
resulting in generation
12
10
11
9
W
PVCC
LG
PGND
ISEN
sets the steady-
1-888-INTERSIL or 1-888-468-3774
R
,
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
Features
• High performance R
• Fast transient response
• ±1% regulation accuracy: -10°C to +100°C and
• Wide input voltage range: +5.0V to +25.0V
• Output voltage range: +0.6V to +3.3V
• Wide output load range: 0A to 25A
• Selectable diode emulation mode for increased light load
• Programmable PWM frequency: 200kHz to 600kHz
• Pre-biased output start-up capability
• Integrated MOSFET drivers and bootstrap diode
• Internal digital soft-start
• Power good monitor
• PWM minimum frequency above audible spectrum
• Fault protection
• Pb-free plus anneal available (RoHS compliant)
Applications
• PCI express graphical processing unit
• Auxiliary power rail
• VRM
• Network adapter
Ordering Information
*Add “-T” suffix for tape and reel.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
ISL6269BCRZ*
ISL6269BIRZ*
PART NUMBER
-40° to +100°C
efficiency
- Undervoltage protection
- Soft crowbar overvoltage protection
- Low-side MOSFET r
- Over-temperature protection
- Fault identification by PGOOD pull down resistance
(Note)
All other trademarks mentioned are the property of their respective owners.
May 30, 2007
|
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2006, 2007. All Rights Reserved
62 69BCRZ -10 to +100 16 Ld 4x4 QFN L16.4x4
62 69BIRZ -40 to +100 16 Ld 4x4 QFN L16.4x4
MARKING
PART
3
technology
DS(ON)
RANGE
TEMP
(°C)
overcurrent protection
ISL6269B
PACKAGE
(Pb-free)
FN6280.2
DWG. #
PKG.

Related parts for ISL6269BCRZ

ISL6269BCRZ Summary of contents

Page 1

... Applications • PCI express graphical processing unit • Auxiliary power rail • VRM • Network adapter Ordering Information PART NUMBER (Note) ISL6269BCRZ* PVCC 12 ISL6269BIRZ* LG *Add “-T” suffix for tape and reel. 11 NOTE: Intersil Pb-free plus anneal products employ special Pb-free ...

Page 2

Block Diagram VIN GND PACKAGE BOTTOM VCC V REF EN − OVP + − UVP + + EA EA − FB COMP − ISEN OCP 30Ω PGOOD PWM FREQUENCY CONTROL + − + ...

Page 3

Typical Application R PGOOD 5V R VCC C C PVCC VCC R COMP C COMP1 C COMP2 R BOTTOM 3 ISL6269B ISL6269B PGOOD VIN PVCC UG VCC BOOT GND PHASE FCCM ISEN EN LG COMP PGND FB FSET VO R ...

Page 4

... Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Ambient Temperature Range ISL6269BCRZ . . . . . . . . . . . . . . . . . . . . . . . . . . .-10°C to +100°C ISL6269BIRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +100°C Supply Voltage (VIN to GND 25V VCC to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V ±5% PVCC to PGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V ±5% = -40°C to +100°C, unless otherwise stated. ...

Page 5

Electrical Specifications These specifications apply for T All typical specifications T PARAMETER ERROR AMPLIFIER FB Input Bias Current COMP Source Current COMP Sink Current COMP High Clamp Voltage COMP Low Clamp Voltage POWER GOOD PGOOD Pull-down Impedance PGOOD Leakage Current ...

Page 6

Electrical Specifications These specifications apply for T All typical specifications T PARAMETER PROTECTION ISEN OCP Threshold ISEN Short-Circuit Threshold UVP Threshold OVP Rising Threshold OVP Falling Threshold OTP Rising Threshold (Note 3) OTP Hysteresis (Note 3) NOTE: 3. Guaranteed by ...

Page 7

... Theory of Operation Modulator The ISL6269B is a hybrid of fixed frequency PWM control, and variable frequency hysteretic control. Intersil’s R technology can simultaneously affect the PWM switching frequency and PWM duty cycle in response to input voltage and output load transients. The term “Ripple” in the name “ ...

Page 8

VOUT VCC and PVCC EN PGOOD 2.75ms FIGURE 4. SOFT-START SEQUENCE The PGOOD pin indicates when the converter is capable of supplying regulated voltage. The PGOOD pin is an undefined impedance if has not reached the rising V VCC ...

Page 9

PWM frequency to a level beyond human hearing when the output load current becomes low enough. With FCCM pulled low, the converter will automatically enter DEM after the PHASE pin has detected positive voltage, while the LG gate-driver pin ...

Page 10

... GATE DRIVERS (EQ. 7) (EQ. 8) FIGURE 6. COMPENSATION REFERENCE CIRCUIT Your local Intersil representative can provide a PC-based tool that can be used to calculate compensation network component values and help simulate the loop frequency response. The compensation network consists of the internal should be checked error amplifier of the ISL6269B and the external components ...

Page 11

... It is assumed that the reader is familiar with many of the basic skills and techniques referenced below. In addition to this guide, Intersil provides complete reference designs that include schematics, bills of materials, and example board layouts. Selecting the LC Output Filter The duty cycle of an ideal buck converter is a function of the input and the output voltage ...

Page 12

MOSFET Selection and Considerations Typically, a MOSFET cannot tolerate even brief excursions beyond their maximum drain to source voltage rating. The MOSFETs used in the power stage of the converter should have a maximum V rating that exceeds the sum ...

Page 13

FCCM (Pin 3), EN (Pin 4), and PGOOD (Pin 16) These are logic inputs that are referenced to the GND pin. Treat as a typical logic signal. COMP (Pin 5), FB (Pin 6), and VO (Pin 8) For best results, ...

Page 14

... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...

Related keywords