IDT72V51253L6BBG IDT, Integrated Device Technology Inc, IDT72V51253L6BBG Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT72V51253L6BBG
Manufacturer Part Number
IDT72V51253L6BBG
Description
IC FLOW CTRL MULTI QUEUE 256-BGA
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.IDT72V51233L7-5BB8.pdf
(50 pages)
Specifications of IDT72V51253L6BBG
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
72V51253L6BBG
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT72V51253L6BBG
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
TABLE 1 — WRITE ADDRESS BUS, WRADD[4:0]
fault mode the user simply has to apply WCLK cycles after a master reset, until
SENO goes LOW, this signals that default programming is complete. These clock
cycles are required for the device to load its internal setup registers. When a
single multi-queue device is used, the completion of device programming is
signaled by the SENO output of a device going from HIGH to LOW. Note, that
SENI must be held LOW when a device is setup for default programming mode.
the first device in a chain can be held LOW. The SENO of a device should connect
to the SENI of the next device in the chain. The SENO of the final device is used
to indicate that default programming of all devices is complete. When the final
SENO goes LOW normal operations may begin. Again, all devices will be
programmed with their maximum number of queues and the memory divided
equally between them. Please refer to Figure 8, Default Programming.
WRITE QUEUE SELECTION & WRITE OPERATION
have up to 4 queues that data can be written into via a common write port using
the data inputs, Din, write clock, WCLK and write enable, WEN. The queue
address present on the write address bus, WRADD during a rising edge on
WCLK while write address enable, WADEN is HIGH, is the queue selected for
write operations. The state of WEN is don’t care during the write queue selection
cycle. The queue selection only has to be made on a single WCLK cycle, this
will remain the selected queue until another queue is selected, the selected
queue is always the last queue selected.
This means that data can be written into the device on every WCLK rising edge
including the cycle that a new queue is being addressed. When a new queue
is selected for write operations the address for that queue must be present on
IDT72V51233/72V51243/72V51253 3.3V, MULTI-QUEUE FLOW-CONTROL DEVICES
(4 QUEUES) 18 BIT WIDE CONFIGURATION 589,824, 1,179,648 and 2,359,296 bits
When configuring the IDT72V51233/72V51243/72V51253 devices in de-
When multi-queue devices are connected in expansion mode, the SENI of
The IDT72V51233/72V51243/72V51253 multi-queue flow-control devices
The write port is designed such that 100% bus utilization can be obtained.
PAFn Flag Bus
Device Select
Write Queue
Operation WCLK WADEN
Select
1
0
FSTR
17
0
1
the WRADD bus during a rising edge of WCLK provided that WADEN is HIGH.
A queue to be written to need only be selected on a single rising edge of WCLK.
All subsequent writes will be written to that queue until a new queue is selected.
A minimum of 2 WCLK cycles must occur between queue selections on the write
port. On the next WCLK rising edge the write port discrete full flag will update
to show the full status of the newly selected queue. On the second rising edge
of WCLK, data present on the data input bus, Din can be written into the newly
selected queue provided that WEN is LOW and the new queue is not full. The
cycle of the queue selection and the next cycle will continue to write data present
on the data input bus, Din into the previous queue provided that WEN is active
LOW.
in to the previous queue.
queue will be prevented, a full queue cannot be written into.
The least significant 2 bits are used to address one of the 4 available queues
within a single multi-queue device. The most significant 3 bits are used when
a device is connected in expansion mode, up to 8 devices can be connected
in expansion, each device having its own 3 bit address. The selected device
is the one for which the address matches a 3 bit ID code, which is statically setup
on the ID pins, ID0, ID1, and ID2 of each individual device.
bus strobe), to address the almost full flag bus of a respective device during direct
mode of operation.
9, Write Queue Select, Write Operation and Full flag Operation and Figure
11, Full Flag Timing Expansion Mode for timing diagrams.
If WEN is HIGH, inactive for these 2 clock cycles, then data will not be written
If the newly selected queue is full at the point of its selection, then writes to that
In the 4 queue multi-queue device the WRADD address bus is 5 bits wide.
Note, the WRADD bus is also used in conjunction with FSTR (almost full flag
Refer to Table 1, for Write Address bus arrangement. Also, refer to Figure
Device Select
(Compared to
ID0,1,2)
Device Select
(Compared to
ID0,1,2)
4 3 2
4 3 2
WRADD[4:0]
Write Queue Address
(2 bits = 4 Queues)
1 0
1 0
X
COMMERCIAL AND INDUSTRIAL
X
5941 drw05
TEMPERATURE RANGES