MT18VDDF6472G-40BG3 Micron Technology Inc, MT18VDDF6472G-40BG3 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT18VDDF6472G-40BG3
Manufacturer Part Number
MT18VDDF6472G-40BG3
Description
MODULE SDRAM DDR 512MB 184DIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT18VDDF12872Y-40BF1.pdf
(31 pages)
Specifications of MT18VDDF6472G-40BG3
Memory Type
DDR SDRAM
Memory Size
512MB
Speed
400MT/s
Package / Case
184-DIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Notes
pdf: 09005aef80f6b913, source: 09005aef80f6b41c
DDAF18C64_128x72G.fm - Rev. C 9/04 EN
10. I
11. This parameter is sampled. V
1. All voltages referenced to V
2. Tests for AC timing, I
3. Outputs measured with equivalent load:
4. AC timing and I
5. The AC and DC input level specifications are as
6. V
7. V
8. I
9. Enables on-chip refresh and address counters.
characteristics may be conducted at nominal ref-
erence/supply voltage levels, but the related spec-
ifications and device operation are guaranteed for
the full voltage range specified.
swing of up to 1.5V in the test environment, but
input timing is still referenced to V
crossing point for CK/CK#), and parameter speci-
fications are guaranteed for the specified AC input
levels under normal use conditions. The mini-
mum slew rate for the input signals used to test
the device is 1V/ns in the range between V
and V
defined in the SSTL_2 Standard (i.e., the receiver
will effectively switch as a result of the signal
crossing the AC input level, and will remain in that
state as long as the signal does not ring back
above [below] the DC input LOW [HIGH] level).
ting device and to track variations in the DC level
of the same. Peak-to-peak noise (non-common
mode) on V
DC value. Thus, from V
±25mV for DC error and an additional ±25mV for
AC noise. This measurement is to be taken at the
nearest V
system supply for signal termination resistors, is
expected to be set equal to V
variations in the DC level of V
rates. Specified values are obtained with mini-
mum cycle time at CL = 3 for -40B with the out-
puts open.
properly initialized, and is averaged at the defined
cycle rate.
V
T
DD
DD
REF
A
TT
DD
= 25°C, V
Q = +2.6V ±0.1V, V
is not applied directly to the device. V
is dependent on output loading and cycle
specifications are tested after the device is
is expected to equal V
IH
(
AC
REF
).
REF
Output
(V
by-pass capacitor.
OUT
OUT
may not exceed ±2 percent of the
)
DD
(DC) = V
V
DD
tests may use a V
TT
50
30pF
, and electrical AC and DC
Reference
Point
REF
DD
SS
DD
DD
Q/2, V
= V
.
REF
Q/2 of the transmit-
Q/2, V
REF
DD
SS
.
, f = 100 MHz,
and must track
= +2.6V ±0.1V,
REF
REF
OUT
is allowed
(or to the
IL
(peak to
-to-V
TT
IL
(
is a
AC
IH
)
18
512MB, 1GB (x72, ECC, SR) PC3200
12. For slew rates < 1 V/ns and greater
13. The CK/CK# input reference level (for timing ref-
14. Inputs are not recognized as valid until V
15. The output timing reference level, as measured at
16.
17. The intent of the Don’t Care state after completion
18. This is not a device limit. The device will operate
19. It is recommended that DQS be valid (HIGH or
20. MIN (
21. The refresh period 64ms. This equates to an aver-
peak) = 0.2V. DM input is grouped with I/O pins,
reflecting the fact that they are matched in loading.
slew rate is < 0.5 V/ns, timing must be derated:
has an additional 50ps per each 100mV/ns reduc-
tion in slew rate from 500mV/ns, while
fected. If slew rate exceeds 4.5 V/ns, functionality is
uncertain. For -40B, slew rates must be 0.5 V/ns.
erenced to CK/CK#) is the point at which CK and
CK# cross; the input reference level for signals
other than CK/CK# is V
lizes. Exception: during the period before V
stabilizes, CKE 0.3 x V
the timing reference point indicated in Note 3, is
V
t
time windows as valid data transitions. These
parameters are not referenced to a specific voltage
level, but specify when the device output is no
longer driving (HZ) or begins driving (LZ).
of the postamble is the DQS-driven signal should
either be high, low, or high-Z and that any signal
transition within the input switching region must
follow valid input requirements. That is, if DQS
transitions high (above V
not transition low (below V
(MIN).
with a negative value, but system performance
could be degraded due to bus turnaround.
LOW) on or before the WRITE command. The
case shown (DQS going from High-Z to logic
LOW) applies when no WRITEs were previously in
progress on the bus. If a previous WRITE was in
progress, DQS could be HIGH during this time,
depending on
smallest multiple of
absolute value for the respective parameter.
(MAX) for I
ple of
value for
age refresh rate of 7.8125µs. However, an AUTO
REFRESH command must be asserted at least
once every 70.3µs; burst refreshing or posting by
HZ and
Micron Technology, Inc., reserves the right to change products or specifications without notice.
TT
184-PIN DDR SDRAM RDIMM
.
t
RC or
t
CK that meets the maximum absolute
t
t
LZ transitions occur in the same access
RAS.
DD
t
t
RFC) for I
measurements is the largest multi-
DQSS.
t
CK that meets the minimum
REF
DD
©2004 Micron Technology, Inc. All rights reserved.
DD
IHDC
Q is recognized as LOW.
.
IHDC
measurements is the
(MIN) then it must
) prior to
0.5 V/ns. If
t
IH is unaf-
REF
t
DQSH
stabi-
t
RAS
REF
t
IS