MT4VDDT1664HY-335F3 Micron Technology Inc, MT4VDDT1664HY-335F3 Datasheet - Page 9
![MODULE DDR 128MB 200-SODIMM](/photos/7/83/78349/mfg_mt_sodimm_series_sml.jpg)
MT4VDDT1664HY-335F3
Manufacturer Part Number
MT4VDDT1664HY-335F3
Description
MODULE DDR 128MB 200-SODIMM
Manufacturer
Micron Technology Inc
Specifications of MT4VDDT1664HY-335F3
Memory Type
DDR SDRAM
Memory Size
128MB
Speed
200MHz
Package / Case
200-SODIMM
Main Category
DRAM Module
Sub-category
DDR SDRAM
Module Type
200SODIMM
Device Core Size
64b
Organization
16Mx64
Total Density
128MByte
Chip Density
256Mb
Access Time (max)
700ps
Maximum Clock Rate
333MHz
Operating Supply Voltage (typ)
2.5V
Operating Current
880mA
Number Of Elements
4
Operating Supply Voltage (max)
2.7V
Operating Supply Voltage (min)
2.3V
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Pin Count
200
Mounting
Socket
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
557-1344
Burst Length
burst oriented, with the burst length being program-
mable, as shown in Figure 5, Mode Register Definition
Diagram. The burst length determines the maximum
number of column locations that can be accessed for a
given READ or WRITE command. Burst lengths of 2, 4,
or 8 locations are available for both the sequential and
the interleaved burst types.
operation or incompatibility with future versions may
result.
of columns equal to the burst length is effectively
selected. All accesses for that burst take place within
this block, meaning that the burst will wrap within the
block if a boundary is reached. The block is uniquely
selected by A1–Ai when the burst length is set to two,
by A2–Ai when the burst length is set to four and by
A3–Ai when the burst length is set to eight (where Ai is
the most significant column address bit for a given
configuration; see Note 5 for Table 6, Burst Definition
Table, on page 10). The remaining (least significant)
address bit(s) is (are) used to select the starting loca-
tion within the block. The programmed burst length
applies to both READ and WRITE bursts.
Burst Type
to be either sequential or interleaved; this is referred to
as the burst type and is selected via bit M3.
mined by the burst length, the burst type and the start-
ing column address, as shown in Figure 6, Burst
Definition Table, on page 10.
Read Latency
between the registration of a READ command and the
availability of the first bit of output data. The latency
can be set to 2 or 2.5 clocks, as shown in Figure 6, CAS
Latency Diagram, on page 10.
and the latency is m clocks, the data will be available
nominally coincident with clock edge n + m. Table 7,
CAS Latency (CL) Table, on page 10, indicates the
operating frequencies at which each CAS latency set-
ting can be used.
operation or incompatibility with future versions may
result.
pdf: 09005aef8086ea3d, source: 09005aef8086ea0b
DD4C8_16_32x64HG.fm - Rev. C 9/04 EN
Read and write accesses to DDR SDRAM devices are
Reserved states should not be used, as unknown
When a READ or WRITE command is issued, a block
Accesses within a given burst may be programmed
The ordering of accesses within a burst is deter-
The READ latency is the delay, in clock cycles,
If a READ command is registered at clock edge n,
Reserved states should not be used as unknown
9
* M13 and M12 (BA1 and BA0)
* M14 and M13 (BA1 and BA0)
64MB Module
128MB and 256MB Modules
must be “0, 0” to select the
must be “0, 0” to select the
base mode register (vs. the
base mode register (vs. the
extended mode register).
extended mode register).
64MB, 128MB, 256MB (x64, SR)
Figure 5: Mode Register Definition
0*
200-PIN DDR SDRAM SODIMM
14
BA1
Micron Technology, Inc., reserves the right to change products or specifications without notice.
0*
0*
13
13
BA1
BA0
0*
12
12
A12 A11
BA0
Operating Mode
11
A11
11
Operating Mode
10
10
A10
A10
M12 M11
0
0
-
9
9
A9
A9
0
0
-
8
8
A8
A8
M10
0
0
-
Diagram
7
7
A7 A6 A5 A4 A3
A7 A6 A5 A4 A3
M9
M6
0
0
-
CAS Latency BT
CAS Latency BT
0
0
0
0
1
1
1
1
6
6
M8 M7
0
1
M5
-
0
0
1
1
0
0
1
1
5
5
0
0
-
M4
0
1
0
1
0
1
0
1
©2004 Micron Technology, Inc. All rights reserved.
4
4
M3
M6-M0
0
1
Valid
Valid
3
3
-
Burst Length
Burst Length
M2
2
2
0
0
0
0
1
1
1
1
A2 A1 A0
A2 A1 A0
CAS Latency
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
M1
0
0
1
1
0
0
1
1
Operating Mode
Normal Operation
Normal Operation/Reset DLL
All other states reserved
1
1
2.5
2
M0
0
1
0
1
0
1
0
1
0
0
Burst Type
Interleaved
Sequential
Reserved
Reserved
Reserved
Reserved
Reserved
Mode Register (Mx)
Mode Register (Mx)
M3 = 0
Address Bus
Address Bus
2
4
8
Burst Length
Reserved
Reserved
Reserved
Reserved
Reserved
M3 = 1
2
4
8