AFBR-57M5APZ Avago Technologies US Inc., AFBR-57M5APZ Datasheet - Page 3

TXRX DGTL DIAGNOSTIC PLUG ETH

AFBR-57M5APZ

Manufacturer Part Number
AFBR-57M5APZ
Description
TXRX DGTL DIAGNOSTIC PLUG ETH
Manufacturer
Avago Technologies US Inc.
Datasheet

Specifications of AFBR-57M5APZ

Applications
Ethernet
Data Rate
2.125Gbps
Wavelength
860nm
Voltage - Supply
2.97 V ~ 3.63 V
Connector Type
LC Duplex
Mounting Type
SFP
Data Rate Max
2.125Gbps
Supply Voltage
3.3V
Wavelength Typ
850nm
Peak Reflow Compatible (260 C)
Yes
Leaded Process Compatible
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
516-1713
517-1713
517-1713

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AFBR-57M5APZ
Manufacturer:
Avago Technologies US Inc.
Quantity:
135
Part Number:
AFBR-57M5APZ
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Figure 1. Transceiver functional diagram.
Transmitter Section
The transmitter section includes consists of the Transmit-
ter Optical SubAssembly (TOSA) and laser driver circuitry.
The TOSA, containing an 850 nm VCSEL (Vertical Cavity
Surface Emitting Laser) light source, is located at the
optical interface and mates with the LC optical connector.
The TOSA is driven by a custom IC which uses the
incoming differential high speed logic signal to modulate
the laser diode driver current. This Tx laser driver circuit
regulates the optical power at a constant level provided
the incoming data pattern is dc balanced (8B/10B code,
for example).
Transmit Disable (Tx_Disable)
The AFBR-57M5APZ accepts a TTL and CMOS compatible
transmit disable control signal input (pin 3) which shuts
down the transmitter optical output. A high signal imple-
ments this function while a low signal allows normal
transceiver operation. In the event of a fault (e.g. eye
safety circuit activated), cycling this control signal resets
the module as depicted in
pull up resistor disables the transceiver transmitter until
the host pulls the input low. Host systems should allow
a 10 ms interval between successive assertions of this
control signal. Tx_Disable can also be asserted via the
two-wire serial interface (address A2h, byte 110, bit 6)
and monitored (address A2h, byte 110, bit 7).
The contents of A2h, byte 110, bit 6 are logic OR’d with
hardware Tx_Disable (pin 3) to control transmitter
operation.
3
OPTICAL INTERFACE
LIGHT FROM FIBER
LIGHT TO FIBER
RECEIVER
TRANSMITTER
Figure 4. An internal
PHOTO-DETECTOR
VCSEL
CONTROLLER & MEMORY
AMPLIFICATION
& QUANTIZATION
Transmit Fault (Tx_Fault)
A catastrophic laser fault will activate the transmitter
signal, TX_FAULT, and disable the laser. This signal is
an open collector output (pull-up required on the host
board). A low signal indicates normal laser operation
and a high signal indicates a fault. The TX_FAULT will
be latched high when a laser fault occurs and is cleared
by toggling the TX_DISABLE input or power cycling the
transceiver. The transmitter fault condition can also be
monitored via the two-wire serial interface (address A2,
byte 110, bit 2).
Eye Safety Circuit
The AFBR-57M5APZ provides Class 1 (single fault tolerant)
eye safety by design and has been tested for compliance
with the requirements listed in Table 1. The eye safety
circuit continuously monitors the optical output power
level and will disable the transmitter upon detecting an
unsafe condition beyond the scope of Class 1 certifica-
tion. Such unsafe conditions can be due to inputs from
the host board (Vcc fluctuation, unbalanced code) or a
fault within the transceiver.
Receiver Section
The receiver section includes the Receiver Optical Sub-
Assembly (ROSA) and the amplification/quantization
circuitry. The ROSA, containing a PIN photodiode and
custom transimpedance amplifier, is located at the
optical interface and mates with the LC optical connector.
The ROSA output is fed to a custom IC that provides post-
amplification and quantization.
CIRCUITRY
DRIVER &
SAFETY
LASER
RD+ (RECEIVE DATA)
RD– (RECEIVE DATA)
Rx LOSS OF SIGNAL
MOD-DEF2 (SDA)
MOD-DEF1 (SCL)
MOD-DEF0
TX_DISABLE
TD+ (TRANSMIT DATA)
TD– (TRANSMIT DATA)
TX_FAULT
ELECTRICAL INTERFACE

Related parts for AFBR-57M5APZ