Z8FMC160100KITG Zilog, Z8FMC160100KITG Datasheet
Z8FMC160100KITG
Specifications of Z8FMC160100KITG
Related parts for Z8FMC160100KITG
Z8FMC160100KITG Summary of contents
Page 1
... Control Development Kit Quick Start Guide Introduction This quick start guide describes how to set up Zilog’s Z8FMC16100 Series Motor Control Development Kit and use it to evaluate your motor control designs and applications. The Z8FMC16100 Series Motor Control Development Kit features a Motor Control Mod- ular Development System (MC MDS) daughter board mounted on a 3-Phase Motor Con- trol Application Board (see Figure 1) ...
Page 2
Table 1. ZDS II System Requirements Recommended Configuration • Windows XP Professional SP3 or later • Pentium IV 2.2GHz processor or Higher • 1024MB RAM or Higher • 135 MB hard disk space (includes Application and Documentation) • Super VGA ...
Page 3
Step 1. Connect the 3-Phase Motor to the Kit The 3-phase motor included with the kit features three spade connectors that plug into spade lugs P1, P2 and P3 on the 3-Phase Motor Control Application Board. Connect ...
Page 4
Speed Potentiometer R7 to its mid-point Refer to the Z8FMC16100 Series Motor Control Motor Control Development Kit User Manual (UM0192) for detailed jumper descriptions. Figure 2. Z8FMC16100 Series Motor Control Development Kit Motor QS005406-0111 Z8FMC16100 Series Motor Control Development ...
Page 5
Step 3. Configure the Universal Power Supply The universal power supply kit features different plug adapters in one box and the power supply in another. The power supply ships with a slide-out plate that must be removed ...
Page 6
Step 6. Apply Power to the Motor The sample code causes Direction SWITCH S1 to change the direction of motor spin. Run/Stop SWITCH S2 is set to turn the motor ON and OFF, and Speed Potentiometer R7 allows you to ...
Page 7
... Explorer, browse to your CD-ROM drive, and double-click the launch.exe file to launch the installer. b. DemoShield provides several installation options. Select Install Zilog Developer Studio to install now. You can install other software and accompanying documentation later. c. Follow the on-screen instructions to complete the installation. ...
Page 8
... When the software has been installed successfully, click Windows XP Observe the following steps to install the USB Smart Cable for Windows XP systems. a. Connect the Zilog USB device to the Host PC. The should activate automatically after connecting the Zilog USB device for the first time; Select No, not at this time QS005406-0111 Z8FMC16100 Series Motor Control Development Kit dialog box is displayed ...
Page 9
... Finish Windows 2000 Observe the following steps to install the USB Smart Cable for Windows 2000 systems. a. Connect the Zilog USB device to the Host PC. The should activate automatically after connecting the Zilog USB device for the first time. b. Click in the Next Found New Hardware c ...
Page 10
... Do not apply power to the MC MDS board or application board unless Caution: the USB Smart Cable is connected both to the host PC and to the devel- opment board’s DBG port. c. Run the ZDS II software. By default, the Zilog Developer Studio II program is located in the Start Programs ZiLOG ZDS II_Z8Encore!_< ...
Page 11
... Figure 4). To view the project source files, double-click the folder on left side of the IDE interface. Double-click the individual Project Files file to open the file in the ZDS II file editor. Figure 4. Zilog Developer Studio II Opening Screen The above figure is for reference only. You may have a newer version of Note: the software. ...
Page 12
Select the correct debug tool using . For example, Select Tool Click for additional information about how to set up the debugger. Note Click . OK i. Click the Rebuild All build to complete as indicated by ...
Page 13
... Use the Direction Switch S1 to change the direction in which the motor spins. Use Speed Potentiometer R7 to adjust the motor RPM. For more information about using Zilog Developer Studio II and building projects for your Z8FMC16100 Series Motor Control Development Kit, refer to the II – ...
Page 14
... Try reloading the sample project as described in Mode using ZDS II on page 6. If you perform these steps and cannot get the sample code to run, contact Zilog Technical Support at www.zilog.com. QS005406-0111 Z8FMC16100 Series Motor Control Development Kit for assistance. ...
Page 15
... Z8, Z8 Encore!, Z8 Encore! XP, Z8 Encore! MC, Crimzon, eZ80, and ZNEO are trademarks or registered trademarks of Zilog, Inc. All other product or service names are the property of their respective owners. QS005406-0111 ...