IS-DEV KIT-7 NKK Switches, IS-DEV KIT-7 Datasheet - Page 10

• Manufacturer Part Number: IS-DEV KIT-7
• Description: KIT DEV FOR OLED SWITCH
• Manufacturer: NKK Switches
• Series: SmartSwitch™r

Specifications of IS-DEV KIT-7

• Main Purpose: Switches with Programmable Display
• Embedded: Yes, ASIC
• Utilized Ic / Part: ISC15ANP4
• Primary Attributes: 2 OLED Switches, PC Board with Flash Memory
• Secondary Attributes: Power and Programming Connections
• Description/function: SMARTSWITCH Development Kit
• For Use With: 360-2431 - SERIAL CBL RJ11-DB9 FOR DEV KIT360-2430 - POWER SUPPLY 240VAC FOR DEV KIT360-2429 - POWER SUPPLY 120VAC FOR DEV KIT
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Smart Switch - OLED
• Other names: 360-2339

7850 East Gelding Drive • Scottsdale, AZ 85260-3420
Step 6D: If timer for switch 2 is expired then:
Step 6E: If the switch 1 is released: Transmit B1H to host if flag is enabled.
Step 6F: If the switch 2 is released: Transmit B2H to host if flag is enabled.
Step 6G: If update flag for switch 1 is set then:
Step 6H: If update flag for switch 2 is set then:
Step 6I: Checks the host communication buffer for data. If there is data, process them. (For detail see
Step 6J: Go to step 6A.
CL01 Intelligent Controller Users Manual B.doc
Send the picture from microSD to OLED module 2 according to current address for switch 2.
Communication Protocol)
1. Transmit 84H to host if flag is enabled.
2. Increment current address for switch 2.
3. If current address for switch 2 is not equal ((end address for switch 2) +1) then:
4. If current address for switch 2 is equal ((end address for switch 2) +1) then:
1. Clear the switch 1 update flag.
2. Transmit FDH and current address for switch 1 to host if flag is enabled.
3. Send the picture from microSD to OLED module 1 according to current address for switch 1.
1. Clear the switch 2 update flag.
2. Transmit FEH and current address for switch 2 to host if flag is enabled.
l. Transmit FEH and current address for switch 2 to host if flag is enabled.
m. Set update flag for switch 2.
n. Read the attributes for end address location for switch 2.
o. If end location action address for switch 2 is equal zero then put current address for switch 2 =
p. If end location action address for switch 2 is not equal zero then:
q. If end location action address for switch 1 is equal zero then take no action.
r. If end location action address for switch 1 is not equal zero then:
start address for switch 2 and set update flag for switch 2.
Toll Free 1.877.2BUYNKK (877.228.9655) • Phone [phone] • Fax [phone]
iii. Get the attributes and put the values for switch 2 action address for switch 1, switch 2
iii. Get the attributes and put the values for switch 1 action address for switch 1, switch 1
iv. Set update flag for switch 2.
iv. Set update flag for switch 1.
ii. Current address for switch 2 = end address action address for switch 2.
ii. Current address for switch 1 = end location action address for switch 1.
i. Start address for switch 2 = end address action address for switch 2.
i. Start address for switch 1 = end location action address for switch 1.
action address for switch 2, end address for switch 2 and timers for switch 2.
action address for switch 2, end address for switch 1 and timers for switch 1.
CL01 Intelligent Controller Users Manual
www.nkkswitches.com • Email [e-mail]
Page 10 of 24
0110