IS-DEV KIT-7 NKK Switches, IS-DEV KIT-7 Datasheet - Page 12

• Manufacturer Part Number: IS-DEV KIT-7
• Description: KIT DEV FOR OLED SWITCH
• Manufacturer: NKK Switches
• Series: SmartSwitch™r

Specifications of IS-DEV KIT-7

• Main Purpose: Switches with Programmable Display
• Embedded: Yes, ASIC
• Utilized Ic / Part: ISC15ANP4
• Primary Attributes: 2 OLED Switches, PC Board with Flash Memory
• Secondary Attributes: Power and Programming Connections
• Description/function: SMARTSWITCH Development Kit
• For Use With: 360-2431 - SERIAL CBL RJ11-DB9 FOR DEV KIT360-2430 - POWER SUPPLY 240VAC FOR DEV KIT360-2429 - POWER SUPPLY 120VAC FOR DEV KIT
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Smart Switch - OLED
• Other names: 360-2339

7850 East Gelding Drive • Scottsdale, AZ 85260-3420
Command to download setup data
[flag] is one byte sent in ASCII HEX format. (Detail below)
[address 1] is two bytes with value of 0001H to FFFFH sent in ASCII HEX format. This is the address for the
image that switch 1 displays upon power up/reboot.
[address 2] is two bytes with value of 0001H to FFFFH sent in ASCII HEX format. This is the address for the
image that switch 2 displays upon power up/reboot.
[reserved] is two bytes sent in ASCII HEX format. This is for future use. Customer could use the last byte for
storing the data version.
This set up data can be read using the attribute upload command.
The controller disables the timers and switch execution upon receiving this command. However, the switches
are still scanned and reported. They are enabled upon reboot/power up or by command from host.
Flag Byte
Example: 2A30303030 3535 3830 30303031 30303146 30303030 sets all the flags on, points left switch to
Command to download an image
[address] is two bytes with value of 0001H to FFFFH sent as ASCII HEX format.
[image] is 6144 bytes transmit in ASCII HEX format.
CL01 Intelligent Controller Users Manual B.doc
The command downloads an attribute block to the EEPROM location.
address 0001H and right switch to address 001FH. The flag takes affect when the controller is reset.
This command downloads an image from the host to the EEPROM location.
command format:
transmit format:
command format:
transmit format:
Bit
B0
B1
B2
B3
B4
B5
B6
B7
Default value=80H
Toll Free 1.877.2BUYNKK (877.228.9655) • Phone [phone] • Fax [phone]
Enable
Value
0
0
0
0
0
0
0
0
CL01 Intelligent Controller Users Manual
Buzzer
61H flag
79H flag
Switch release report flag
6EH flag
Timers expire report flag
Switch press report flag
Address change report flag Newest address is reported for each switch
(xxH) (xxAH) (xxAH)
28H
(xxH)
2AH
www.nkkswitches.com • Email [e-mail]
[address] [image]
(xxAH)
[00H]
Flag
(xxAH)
[00H]
(xxAH)
[55H]
Beeper sound for switch press
61H is transmitted in response to command.
79H is transmitted upon completion of
command.
Switch release are reported
6CH/6EH is transmitted if there is any error
during communication to host.
Timers expiration are reported
Switch presses are reported
Controller action when flag is set
(xxAH)
[flag]
[address1]
(xxAH)
[address2 ]
(xxAH)
[reserved]
(xxAH)
Page 12 of 24
0110