TL71 Fluke Electronics, TL71 Datasheet - Page 43

• Manufacturer Part Number: TL71
• Description: TEST LEAD SET 10A
• Manufacturer: Fluke Electronics

Specifications of TL71

• Current Rating: 10A
• Termination: Banana Plug, Sheathed, Right Angle
• Color: Black and Red - Plugs and Wire; Gray - Probes
• Ratings: CAT IV, 600V; CAT III, 1000V
• Wire Insulation Material: Silicone
• Includes: Pin Tip
• For Use With: 614-1085 - MULTIMETER INDUSTRIAL 1000V CATFLUKE-116 - MULTIMETER HVAC TRUE RMS614-1061 - DMM TRUE RMS 50000CNT W/BCKLGHT614-1020 - DMM TRE RMS W/BCKLGT 6000CNT DIS
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Max: -
• Impedance: -
• Cable Length: -
• Other names: 1274382; 614-1054

Specifications – 789 and 787 ProcessMeter
Temperature range of 18 °C to 28 °C, for one year after calibration
Maximum voltage applied between any jack and earth ground:1000 V rms Storage temperature: -40 °C to 60 °C
Operating temperature: -20 °C to 55 °C Relative humidity: 95 % up to 30 °C; 75 % up to 40 °C; 45 % up to 50 °C; 35 % up to 55 °C
Safety: Designed in accordance with EN61010, ANSI/ISA S82.01-1994 and CAN/CSA C22.2 No. 1010.1-92 Over-voltage CAT III
Size (HxWxL)/weight (787 with holster): 52 mm x 98 mm x 201 mm (2.06 in x 3.86 in x 7.93 in)/638 g (1.4 lb)
Size (HxWxL)/weight (789): 50 mm x 100 mm x 203 mm (1.97 in x 3.94 in x 8.00 in)/600 g (1.3 lb)
Recommended accessories – 787 and 789 ProcessMeter
For more information and detailed specifications, go to www.fluke.com/processmeters
Measurement function
V dc
V dc (true-rms)
mA dc
A dc
A ac
Resistance
Frequency (0.5 Hz to 20 kHz)
Diode Test
Continuity
Output function
DC current output (Internal
battery operation)
DC current simulate
(Ext. 24 Volt loop supply,
up to 48 V on 789 only)
24 V loop supply
Current adjustment modes
SureGrip Industrial
Test Lead Set
See page 61
Safety rated multimeters with mA source
TL0
ProcessMeter
Meter Hanging Kit
See page 71
ToolPak
Best accuracy range and resolution
400.0 mV, 4.000 V, 40.00 V, 400.0 V, 1000 V
400.0 mV, 4.000 V, 40.00 V, 400.0 V, 1000 V
30.000 mA
1.000 A (0.440 A continuous)
1.000 A (0.440 A continuous)
400.0 W, 4.000 k, 40.00 k, 400.0 k, 4.0 M, 40 M
199.99 Hz, 1999.9 Hz, 19.999 kHz
789: 2.000 V (shows diode voltage drop) 787:
2.400 V (shows diode voltage drop)
Beeps for resistance < approx. 100 ohms
Range and resolution
0.000 mA to 20.000 mA or 4.000 mA to 20.000 mA
(selectable at power-up) Over-range to 24.000 mA
0.000 mA to 20.000 mA or 4.000 mA to 20.000 mA,
(selectable at power-up) Over-range to 24.000 mA
789: Minimum 24 V 787: not available
Manual: Coarse, Fine, 25 % and 100 % step
(100 % step 789 only) Automatic: slow ramp,
fast ramp, 25 % step
Fluke 789 and 787
Fluke 789 ProcessMeter
With the Fluke 789 ProcessMeter, process technicians
can do a lot more while carrying a lot less.
Key Fluke 789 features:
•
•
•
•
•
•
•
•
•
Fluke 787 ProcessMeter
•
•
•
•
24 V loop power supply
HART mode setting with loop power
(adds 250 ohm resistor)
Double-sized, dual display
20 mA drive into 1200 ohms
Backlight with two brightness settings
0 to 100 % mA Span Check buttons to toggle between
4 mA and 20 mA
Infrared I/O serial port compatible with FlukeView
Forms Software
Improved battery power with four AA batteries
Plus all the proven 787 features
Simultaneous mA and % of scale readout on mA output
25 % Manual Step plus Auto Step and Auto Ramp on
mA output
Min/Max/Average/Hold/Relative modes
Externally accessible battery for easy changes
Temperature Probe
See page 69
80T-150U
Universal
(Fluke 789 only)
IEC 1010-1
CAT
Designed and
Conforms to
600
™
V
IV
Test Tools
See page 70
Meter Case
C15
789: 24 V compliance
1000 Ohms, @ 20 mA
500 Ohms, @ 20 mA
250 Ohms @ 20 mA
@ 20 mA 787: 12 V
Drive capability
or, 1,200 Ohms,
compliance or,
(% of reading + LSD)
2 % + 1 2 % + 1
.005 % + 1
0.1 % + 1
0.7 % + 2
.05 % + 2
0.2 % + 2
0.2 % + 1
Pressure Vacuum Module
1 % + 2
See page 65
PV50
(% of span)
Accuracy
> 24 V
.05 %
.05 %
®
Application note, literature code
2041342:
In-field valve positioner
checks
Valve positioners
open and close
with a 4 to
20 mA signal
applied. This
application note
explains how to
adjust these
valves so they
open and close
correctly.
Want to read
more? Download
this and other
application notes
at www.fluke.com/library
Included accessories
Fluke-789 ProcessMeter: TL71
Premium Safety-Designed Test Lead
Set plus alligator clips, 4 AA alkaline
batteries (installed), product overview
and users manual (CD-ROM) in
14 languages.
Fluke-787 ProcessMeter: Protective
yellow holster with test lead storage,
TL75 Safety-Designed Test Lead Set
plus alligator clips, one 9 V alkaline
battery (installed), product overview
and users manual (CD-ROM) in
14 languages.
Ordering information
Fluke-789 ProcessMeter
Fluke-787 ProcessMeter
Process Calibration Tools