PIC16F1937-I/P Microchip Technology, PIC16F1937-I/P Datasheet - Page 269

• Manufacturer Part Number: PIC16F1937-I/P
• Description: IC PIC MCU FLASH 512KX14 40-PDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1937-I/P

• Program Memory Type: FLASH
• Program Memory Size: 14KB (8K x 14)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: EUSART/MI2C/SPI
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14-ch x 10-bit
• A/d Bit Size: 10 bit
• A/d Channels Available: 14
• Height: 4.95 mm
• Length: 53.21 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Width: 14.73 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

23.6.2
Clock arbitration occurs when the master, during any
receive, transmit or Repeated Start/Stop condition,
releases the SCL pin (SCL allowed to float high). When
the SCL pin is allowed to float high, the Baud Rate Gen-
erator (BRG) is suspended from counting until the SCL
pin is actually sampled high. When the SCL pin is sam-
pled high, the Baud Rate Generator is reloaded with
the contents of SSPADD<7:0> and begins counting.
This ensures that the SCL high time will always be at
least one BRG rollover count in the event that the clock
is held low by an external device (Figure 23-25).
FIGURE 23-25:
23.6.3
If the user writes the SSPBUF when a Start, Restart,
Stop, Receive or Transmit sequence is in progress, the
WCOL is set and the contents of the buffer are
unchanged (the write doesn’t occur). Any time the
WCOL bit is set it indicates that an action on SSPBUF
was attempted while the module was not idle.
 2009 Microchip Technology Inc.
Note:
CLOCK ARBITRATION
WCOL STATUS FLAG
Because queueing of events is not
allowed, writing to the lower 5 bits of
SSPCON2 is disabled until the Start
condition is complete.
SDA
SCL
BRG
Value
BRG
Reload
BAUD RATE GENERATOR TIMING WITH CLOCK ARBITRATION
03h
DX
SCL deasserted but slave holds
SCL low (clock arbitration)
02h
SCL is sampled high, reload takes
place and BRG starts its count
01h
Preliminary
BRG decrements on
Q2 and Q4 cycles
00h (hold off)
PIC16F193X/LF193X
DX ‚
–
1
SCL allowed to transition high
03h
02h
DS41364D-page 269