DSPIC30F5013-20I/PT Microchip Technology, DSPIC30F5013-20I/PT Datasheet - Page 174

• Manufacturer Part Number: DSPIC30F5013-20I/PT
• Description: IC DSPIC MCU/DSP 66K 80TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F5013-20I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 66KB (22K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of I/o's: 68
• Flash Memory Size: 66KB
• Supply Voltage Range: 2.5V To 5.5V
• Package: 80TQFP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 68
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 16-chx12-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPDM300004-2 - BOARD DEMO DSPICDEM.NET 2DM300004-1 - BOARD DEMO DSPICDEM.NET 1AC30F007 - MODULE SKT FOR DSPIC30F 80TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DSPIC30F501320IPT

dsPIC30F5011/5013
TABLE 23-14: EXTERNAL CLOCK TIMING REQUIREMENTS
DS70116J-page 174
AC CHARACTERISTICS
OS10
OS20
OS25
OS30
OS31
OS40
OS41
Note 1:
Param
No.
2:
3:
4:
F
T
T
TosL,
TosH
TosR,
TosF
TckR
TckF
Symbol
OSC
CY
OSC
Data in “Typ” column is at 5V, 25°C unless otherwise stated. Parameters are for design guidance only and
are not tested.
These parameters are characterized but not tested in manufacturing.
Instruction cycle period (T
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits may result in an unstable oscillator
operation and/or higher than expected current consumption. All devices are tested to operate at “Min”
values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the
“Max” cycle time limit is “DC” (no clock) for all devices.
Measurements are taken in EC or ERC modes. The CLKOUT signal is measured on the OSC2 pin.
CLKOUT is low for the Q1-Q2 period (1/2 T
External CLKIN Frequency
(External clocks allowed only
in EC mode)
Oscillator Frequency
T
Instruction Cycle Time
External Clock
High or Low Time
External Clock
Rise or Fall Time
CLKOUT Rise Time
CLKOUT Fall Time
OSC
= 1/F
Characteristic
OSC
(2)
(2)
in (OSC1)
in (OSC1)
CY
(2,4)
(2,4)
) equals four times the input oscillator time base period. All specified values
(2)
(2,3)
(2)
Standard Operating Conditions: 2.5V to 5.5V
(unless otherwise stated)
Operating temperature
T
.45 x
Min
DC
DC
0.4
OSC
10
—
—
33
—
—
—
CY
4
4
4
4
4
4
4
) and high for the Q3-Q4 period (1/2 T
32.768
Typ
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
(1)
Max
7.5
7.5
DC
40
10
10
10
10
10
25
20
—
—
—
—
—
-40°C ≤ T
-40°C ≤ T
4
4
Units
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
A
A
kHz
—
ns
ns
ns
ns
ns
≤ +85°C for Industrial
≤ +125°C for Extended
© 2011 Microchip Technology Inc.
EC
EC with 4x PLL
EC with 8x PLL
EC with 16x PLL
RC
XTL
XT
XT with 4x PLL
XT with 8x PLL
XT with 16x PLL
HS
LP
See parameter OS10
for F
See
EC
EC
See parameter
See parameter
CY
OSC
Table 23-17
).
Conditions
value
DO31
DO32